Hello nordic community,
i have custom board that have nRF5340 and nRF7002, our requirement is to use wifi every 5 minutes (connect send data and disconnect) but randomly...
HI,
I am using the periodic_adv_rsp example from version 3.0.0. I would like to ask how to switch channels and transmission power in the example code?
Thanks.
Hello team,
We have a problem here, we are running a new program with 5 years long-term standby IOT device, once we are trying to use SMS to configure the IOT device we...
In our development using NCS-2.6.1 it is desirable to have logs using BT NUS.
"Serial Bluetooth Terminal" android application is used.
For testing purposes NCS\v3.0.2...
Hi,
I want to port an exisiting solution from ESP32 + nrf24 to nrf54L15. I didn't find any example that would work out of the box for my POC which would to combine very...
I'm in the process of upgrading one of our applications from NCS 2.6.1 to 3.0.1. According to this document, the only versions of NCS that support modem firmware 2.0.1 and...
Just want to check if NRF52832 or NRF52840 can communication with iPhone 7 as instead of W1, which can transfer the data and audio from iPhone to earphone base on NRF52832...
While creating my own service I used ble_app_blinky as an example, once I opened ble_lbs.c file I saw it contains the service's declaration inside the macro:
#if NRF_MODULE_ENABLED...
I'm using nRF52 + SDK11.0.0 + s132. I have an SPI slave configured. I have 40B data being read by a master every 12ms at 1MHz SPI clock. The master is trigger to do the read...
HEY
I am using my nrf 51 dk too program the nrf51822 board externally. How I can identify the board in keil, only the 51 dk is shown in the debug settings. How i can select...
I would like to see output from NRF_LOG_DEBUG in the Rtt Viewer, to achieve that I changed (in sdk_config.h)
#define COMMON_CONFIG_LOG_LEVEL 4
#define NRF_LOG_BACKEND_SERIAL_USES_RTT...
Hi all!
These days I've developed a custom SAADC + UART program to fulfil my needs using the SAADC example in the SDK 11. I've tested it and all is working really fine...
I have 1 dongle and 2 NRF52DKs attached to my computer at the same time, when I am trying to use Keil to program just 1 board it seems like attempts to access all 3 my boards...
NFC examaples in SDK 12.2 and 13.0.0-1.alpha on nRF52832 (board PCA10040) may not work if HAL_NFC_FIELD_TIMER_PERIOD is set to a value higher than 255. HAL_NFC_FIELD_TIMER_PERIOD...
To my very limited knowledge, it has something to do with an "attribute table" of some sort. So you will have an init function, where you get to write all your attributes...
I use active scanning ，the observer will send a scan request when it hears and advertiser, and will listen for a scan response.I only see the scan event，but sent request and...
hello in nrf51 sdk, nordic has already ported freertos.
but if i want to port myself. can anyone tell me how to do it??
first i downloaded freertos from website. but then...
Hi,
I am new to nrf and trying to make some new services and characteristics for my device.
I followed the advertising , services and characteristics tutorial and was...
hello there i have ble_uart code . when i run on nrf51 dk and when i see it on mastercontrol pannel app. i got that type of screen shot!!
means when i write into characteristics...
NRF2460 is linked，I can transfer 3 byte data. But sometimes it is mute, not always.
Register I2SCNF_OUT bit6 is zero.
I am appreciate for your advices.
