Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Hi,
I've written an app on the nrf51822 (rev2), with S110 (v7.3.0) and SDK v6.1.0. I've written a custom non-blocking UART driver. I'm running into an issue where the UART...
Hi,
Using the nRF5 11.0.0 release SDK, I'm trying to set up one task to transmit to and one task to receive data from the UART. Nothing special.
The configuration block...
Hi,
The xQueueReceive function in FreeRTOS seems to be broken, when a non-zero timeout is specified.
Example, I'm trying to create and ordered output mechanism for the...
Hello there,
I managed successfuly to build the 'ble_app_hrs' of SDK10 on my NRF51 on GCC MARS 2.0 using these two guides combined:
devzone.nordicsemi.com/.../
devzone...
When i use the nrf_drv_adc with NRF_ADC_DEFAULT_CONFIG i get the following compile errors:
rf_drv_adc.h:127:27: error: 'ADC_CONFIG_IRQ_PRIORITY' undeclared here (not in...
I am developing a real-time system which triggers an interrupt every few milliseconds. That data is collected in the interrupt. When a memory buffer is full, the data is then...
Hi,
i am trying to start a RTC0 on nrf52 DK with SoftDevice (s132) enabled with project based on "ble_app_template". The problem is that a sd_softdevice_enable() (called...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have setup a development environment using Eclipse and GCC. This setup works nicely. Thanks!
devzone.nordicsemi.com/.../
I noticed different examples in...
Hello,
We are currently designing the hardware for a production run of our product using the nrf52832 chip and would still like to have debugging capabilities with breakpoints...
I have been learning GCC+ Make work flow to build and debug nRF51822 S110-only applications based on the examples from NRF51 SDK v10.0.0. I started with ble_app_beacon example...
I tried to work application.
But firmware stops at advertising_init(). When I exchange advertising_init() and services_init(), firmware does not stop.
why ?
S110 v8.0...
Hello,
My device is nRF51822 SD110 8.0.0.
The problem occured after firmware update in bootloader (own, not SDK) with readback protection enabled.
So bootloader connects...
Hello,
I am currently finishing my deploy script and I am currently using nrfjprog to write some custom UICR data. I have a contiguous region of memory to write but I do...
Dear Nordic team,
Beside other persistent issues with your proprietary DTM command for setting Tx Power (see here and here ) I've found that default Tx Power in ble_dtm...
