I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Hi
The 840 datasheet (page 90) states that the HFINT tolerance is +/-1.5% typical and +/-8% max.
Under normal operation, the HFINT is running and so if the device (like...
I was beyond excited to see all the support Nordic was providing to the mbedOS project.
All of a sudden it disappeared.
If not supporting mbed the alternatives would...
Hello,
We have an nrf51822 system where disconnecting the battery is problematic, and the sharing of the reset line between SWD and reset function has been a real source...
Hi. I'm beginner of nRF.
I want to get some data from a temperature sensor, but I don't know how to assign a pin. Also, how can I check the data ??
In Arduino, there...
Hello,
I'm attempting to include the "arm_math.h" library so that I can use the requisite DSP functions, etc. I'm getting a linker error so I'm not sure what else needs...
HI,
I am using nRF52832 and SDK 14.2 and trying to send MPU accelerometer values to android device through BLE . But when I call " mpu_init() " in main function to initiate...
Dear Sir,
I am new to Nordic. This is my first query. It is related to running Timer with softdevice. I am using TIMER1 ( as const nrf_drv_timer_t TIMER_LED = NRF_DRV_TIMER_INSTANCE...
Hi, Support team,
When I use the SPI peripheral communicate with nrf24l01+,it's no data return in m_rx_buf by using the API nrf_drv_spi_transfer(&spi,m_tx_buf,1, m_rx_buf...
Hi,
I use the FDS on our project firmware. The firmware saves some configurations to FDS at shutdown and the factory reset. At this time, sometime fds_gc() does not call...
Sometime, the timer handler is not call immediately after calling app_timer_start().
environment - nrf52840 - SDK 15 - with FreeRTOS - timer task priority is higher - timeout_ticks...
Hi,
In the nRF Mesh mobile app, when you go to the settings tab, you can hit "Reset Network", this appears to clear any previously provisioned network, and lets you start...
Hi all!
We've been time-stamping GPIO events using PPI in nRF52 , and it works* !
...but when using the SoftDevice , it apparently clashes with the PPI about 30ms after...
Hello,
I have been having issues when using the UART libraries (app_uart.h) with certain pins on the nrf52832. Previous iterations of our project have worked correctly but...
I am investigating an H4 HCI over a UART implementation for a client which plans to use the 52832 (or 52840) as a replacement for a TI BLE chip in a new design.
I have built...
