Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi,
We have the following problem when start the watchdog from bootloader: the application is started successfully by the bootloader but when enable the softdevice the application...
Hello, I'm implementing a pair of MCUs where one is operating a ANT+/BLE radio stack using the S332 soft device. Whilst TWIS is disabled, we're getting great performance,...
Hi all , I using module NRF52832 and SDKv14 . I have 2 board central and 2 board peripheral . I want to connect each board central to all board peripheral and connect each...
Hi everyone,
I'm working in an application for a wearable device and I recently have a problem debugging it with Ozone Debugger from SEGGER Microcontroller Systems . I'm...
Hi I am using the mesh sdk 2.0.1 and the nrf52 dk board.
I have made a new model modifying the simple on of client/server example, where the server will send a periodic...
the function nrf_dfu_settings_init in nfu_dfu_setting.c
// Copy the DFU settings out of flash and into a buffer in RAM.
memcpy((void*)&s_dfu_settings, m_dfu_settings_buffer...
Hi,
Our product is based on BLE 4.2 / 5 peripheral devices and PC application (windows 7 & 10 environment) as central device.
we try to use nRF52840 dongle and also other...
On a NRF52DK Board, There is an on-board programmer done with ATSAM3U2C seen as a Segger programmer or a Jlink Progammer.
By mistake, I erased the entire flash of this...
I was trying to update J-link firmware (using link [https://devzone.nordicsemi.com/question/170895/nrf52832-jlink-stop-working-after-entering-bootloader-mode/] ) into interface...
Hi,
The following vulnerability described as Bluetooth implementations may not sufficiently validate elliptic curve parameters during Diffie-Hellman key exchange in the...
I want to use the serial DFU. Do you have any examples? I tried with ble_app_buttonless_dfu, not UART DFU.If you have a detailed reference, please let me know.thank you very...
Hi,
I am using the MCU on a board with sensors that are sampled in a very high rate (~100Hz).
I am having issues when trying to send the data with notification on more...
Hi,
I am using sdk12.2 and customised nrf52 board.
I want to interface ultrasonic sensor with nrf52. In this I am enabling trigger pin as high and after sometime my...
Dear All,
I am working with SDK version 15 and softdevice 132.
I want the device to advertise for 1 minute. Then go to low power mode. Again wake up after 5 minutes...
I have twe NRF24L01 module,one set Tx mode with autoask,and another set Rx mode without autoask,
The channel and address are same.
Can I use this mode to communication...
