Hi Nordic team!
I haven't been able to implement the joiner functionality on a Thread network with nrf52840. I'm using the nRF52840-DK as the leader. For the DK, I follow...
I run a large research lab using hundreds of nRF52840 DKs. These boards are periodically rotated between active experiments and storage. Because boards are pulled from storage...
Hi,
I am using an nRF54L15 and I would like to explicitly enable the HFCLK (32MHz). I want to use it to drive TIMER00, which will run during the whole application runtime...
Hi all,
I am working on a project that requires me to run the SHAKE128 and SHAKE256 algorithms as specified in FIPS 203. I am wondering if it is possible to implement these...
Environment
SoC: nRF54LM20A (cpuapp, non-secure / TF-M)
nRF Connect SDK: v3.3.0
sQSPI soft peripheral driving an AMOLED display via the FLPR
BLE active via MPSL...
Hi,
We had connectivity issues on our end for the Message Routing Service webhook since May 13, 2026. It has been restored and tested with the nRF Cloud verification test...
Hi,
I see the different behavior of the function sd_ble_gap_conn_param_update when connected to Windows integrated Bluetooth.
Using bare-metal SDK v0.9.0 it succeeds...
In fact, I would like to know if there are receivers from Nordic, able to receive simultaneous (or with time slot management) data from transceiver (type nRF52). I can use...
Is there any Dc offset on nRF52840 RF port? Is it necessary to add a DC blocking capacitor if the load has DC path to ground?
In particular Is it OK to connect a 50 Ohm...
I have read articles on the forum, watch youtube but still no luck. Actually I failed to find step by step tutorial how to do it from start to the end. Most of them touch...
Hello,
I'm trying to flash my nRF52 board with my program and for some reason it's freezing/crashing in the middle of programming the device using "nrfjprog". When I try...
Hi,
I am trying to find a good solution for multiple beacon advertising using s132_nrf52_3.0.0_softdevice and sdk 12.1 on nrf52.
Looking at other similar threads:
...
Hi, there
NRF51822
SDK9.0.0 and S110
How to subcontract in uart nus mode to ensure that each packet does not exceed 20 bytes and is sent as quickly as possible...
Wakeup from system off (not WFE) )will cause a system reset and hence will reset almost all of the peripherals (exceptions are RAM and few registers). RTC will also be rest...
Hello,
Is there a BLE only DFU application like that available on Android? The Android application works fine. The windows version needs a serial port to perform the same...
For synchronizing an external sensor i need to output a 32768Hz clock at a GPIO pin. For this case i want to use LFCLK from the external cyrstal.
My setup:
I use RTC0...
Hello,guys
I have build one application, in which I want to transmit the Image from Mobile BLE to nrf51822 and than after display on display like E-paper.
The use case...
Hi,
I use it as a translator for Google, so it may be strange in context. please understand.
I was in big trouble.
I used the nRF51822, S110, and SDK9 in my previous...
Hi. We are attempting to use the Infineon XMC1202 LED shield with our NRF52 device. The XMC1202 has an I2C address of 0x15E, instead of the traditional 7 bit address. We have...
I've tried linking the ESB library (esb_arm.lib) in Eclipse by adding it to my nRF51822 project's Makefile, but I am still getting undefined reference errors during build...
Hi
We are going to use the Taiyo Yuden Evaluation Board - EBSHJNZWZ.
As i understand, the board firmware used the Nortic SoftDevice S132
The question is :
May i...
