I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
I am working in a project.The project had defined the manuf_data that it didn't need the company_identifier(bluetooth core 4.0). Is there any way does not show company_identifier...
Hi,
This is a request for all the users to post some details of sensors they are using along with Nordic chips. We will get familiar with 10 most popular sensors that are...
I am trying to build PCA10040 examples but I am getting the following error:
make genhex
Preparing: .hex
/home/me/nrf52/gcc/gcc-arm-none-eabi-4_9-2015q1/bin/arm-none...
Hi guys
I am planning to develop a beacon app, but I am not sure what would be the minimum scanning interval in order to keep the phone's battery drain on a fairly good...
Hi, I use the following.
Raspberry Pi 3 (RPi3 with Raspbian Jessie 4.4) as a router,
RPi3 is connected to a Wi-Fi router to access the Internet by using the built...
Hi, there! nRf Toolbox drove me crazy!! can anyone help me?
I flash "s130_nrf51_2.0.0_softdevice.hex" to the pca10028 board.
I compile the bootloader example "nRF5_SDK_11...
Hi,
I'am having an issue with UART using app_uart_fifo.c (SDK 0.9.2). At times I get communication error (usually at attaching and detaching uart connector) and my error...
Hi.
I'm little worried about our bt sensor power consumption.
We are using twi/i2c to communicate with sensors periodically. We are using app timer to trigger these...
I have a custom board that doesn't use the external 32Khz crystal. The engineer that designed it chose to use P0.0 as UART RX. (I know, poor choice.) I have set up a custom_board...
I am using SDK_11 s130. I see APP_ERROR_CHECK(err_code) being used throughout the SDK examples. When err_code is any value other than NRF_SUCCESS, the nRF51-dk board will...
Previously, I was able to program ble_app_uart using SDK_11 s130 into nRF51-dk. Now, I would like to program ble_app_uart into Adafruit Bluefruit LE friend board. www.adafruit...
I have been following the advertising tutorial and decided to start my own application using nordics git repo as a reference. After a few debug sessions I found that I needed...
I am trying to probe sysclk signal on one of the unused GPIO pins on a nRF52 board. I modified the ble_app_template example provided in SDK 11.0.0 and added a sysclk function...
I am trying to connect nRF52 with 7120 and create a NFC card reader , is this a solution and power efficient solution .
I will interface through I2C , is there a example...
I am using the sdk version 11 and arm-none-eabi-gcc version 5.4 on linux mint to compile the blinky test application. I have pointed the Makefile-posix at the location of...
