Hey everyone,
Does anyone here have experience with firmware OTA updates over the JIO NB-IoT network? The process seems a bit different since JIO Cloud always sits between...
Hello:
The latest nRF54L15 Errata for Rev 2 shows that the previously reported "GPIOs can exhibit radiated emissions" is no longer present in the Rev 2 SoC.
Can you please...
Hi, this is a very broad issue that i am having, because i dont know the source of it. I am simply unable to use the bme68x IAQ library. i have downloaded the external bsec...
Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hello,
i am using the nrf51822 with softdevice s110. In the spec i read that the contoller works as well with an external 32khz reference which i want to use. The oszillator...
hello everyone,
i use nrf51822 and i want to use one switch that wakeup the module from sleep mode. so can i connect switch to gpio of nrf51822 module. if yes than which...
I'm a newbie so bare with me. I had this code running, saved it, and started another project. I tried not to touch any of the files I had running with the example below, but...
application note nAN-034 describes two alternatives for production testing an application using the nRF51822. One method is using a commercial tester (MT8852) and the other...
I need to send data PIR motion detector sensor to the master controller in my motion detector network.
Can I get away with just one of the nrf51 chips and my PIR sensor...
We're trying to decide at what voltage we should run our nRF51822 on the next revision of our board. To date we've been doing fine at 1.8V. The current drawn on a 3.7V lithium...
hi, i made ble app including bootloader using nRF51822 (s110), sdk 6.1.0
when i use sd_nvic_SystemReset() function in app, it erase app's pstorage.
But i want to preserve...
Hi,
I use S120 as central device and I need to handle multiple connections.
However S120 works quite unclear to me.
If S120 doesn't reply to BLE_GAP_EVT_CONN_PARAM_UPDATE_REQUEST...
Hello ,
I am trying to develop an application using the S130 soft device using Keil MDK v5 Lite. I have came to know that it is not possible to generate a code size greater...
I've run into a problem using the provided spi master code.
I get the following error message from Keil
spi_master.c(381): error: #1059-D: an entity with an internal...
Hi
I want to run the ble_proximity template on micro blend (Readbear lab). But I can't make it to work. I have uploaded the code to the board and using the nRF Proximity...
Hi all, I have followed the steps described
https://devzone.nordicsemi.com/question/14780/nrf51822-development-kit-without-nrfgo-starter-kit/
with the alternative power...
Hi,
I have successfully implemented a HID keyboard, using the nRF8001 and arduino sdk 0.9.1 ported to a microchip PIC18F controller. Connecting to iPhone iOS7.1.2
Everything...
hello,
please find main.c file of code and how to add the MAC address to the ble_app_hrs sample code
that was provided in the samples directory of the SDK.
Can you...
hi,
I am trying to develop a network of ble devices.i want nrf51822 to function as a master and slave( not necessarily simultaneous). For that i need to develop a custom...
