Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hello,
I have a product based on nRF9160 that uses GNSS. The device is a meter, not an asset tracker, so GNSS is not the TOP 1 feature we need.
When the device is installed...
Hello everyone,
I'm curretly working on a new design based on nrf52832, and I'm validating different interfaces. Currently working on SPI, I'm testing it with a W25Q64...
Does bootloader example dfu_dual_bank_ble_s132_pca10040 from SDK v11 work with softdevice v3.0?
when I try to run the dfu_dual_bank_ble example with softdevice 3.0, I got...
Hi ,
I have 2 nrf51 dongle compiled with a code which can scan and advertise ibeacon constantly. Whenever receive advertisement packet from each other , they are able to...
Hello,
I'm running one advertiser and one scanner at the same time, and I want to change the data inside the advertise packet, every advertise. Looking at the forum and...
I use two nRF51822 boards running the ble_mesh_gateway sample project. I have modify the project slightly so to work on my board(juts modify the GPIO configuration , LED and...
Hi all, Now I'm working secure bootloader in sdk12 for these I installed the nrfutilv1.5.0 by following nrfutil user guide
link text
while I'm creating .zip files it...
I've seen similar questions posted, but none that match my situation exactly and those solutions did not work for me.
I'm using the pca10040 dev kit, which I connected...
For the radio peripheral, if I use a shorts (shortcut) from END to DISABLED states, is EVENT_END still set? Because I enable an interrupt on EVENT_END, but not on EVENT_DISABLED...
Does anyone know how to remove all Nordic software and clean out all registry keys?
Installed mastercontrolpanel.3.9.0.6.x64.msi and all is working great with the RF Dongle...
Hello together,
i have a question to the uart hardware communication.
I try to send 6 bytes from the nRF51 DK, S130, SDK12 (p0.09 tx) pin to another hardware rx pin.
...
Hi,
Trying to add DFU service on the new SDK, but when compiling getting this:
compiling nrf_dfu_flash.c...
..\..\..\..\..\..\components\libraries\bootloader\dfu\nrf_dfu_flash...
I'm using SDKv12 S132v3 on nRF52 peripheral device. I have characteristic with following security setup:
char_add_params.read_access=SEC_JUST_WORKS;
char_add_params.write_access...
Is it possible that a crash in code can prevent connection by SWD to an nRF51822?
As I had an instance this morning, where after uploading, some code to a smart watch,...
I'm trying to use a 32 bit service UUID, but it doesn't seem to be supported by SDK 10 or SDK 12
Looking in the HRS it has this code
BLE_UUID_HEART_RATE_SERVICE, BLE_UUID_TYPE_BLE...
Hi,
I am using App Timer for measuring time and at the same time while loop to check if the timer reached particular time.
I have noticed during while loop App Timer...
