Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
I'm using s120 v2.1, with SDK 9, on an nRF51 with 256K ROM and 16K RAM. With s120 I only have 6K of usable RAM for my application. I am running critically low on RAM, and...
I am using a nRF51 dongle as a BLE tranciever and using UART to communicate with an 8bit AVR. I used BLE_APP_UART peripheral example and mostly just changed the pins used...
Hi,
I am trying to update the battery level of my Battery Service but get keep getting an error. The error code is : 0x00003002. I cannot find any mention of what this...
I am trying to start programming in nrf51822 module with the waveshare kit. but the kit always shows the error as switch to boot-loader mode . how to solve this problem?
i am using nrf51822 wavshare kit with ulink2 debugger.
when ever i try to program the kit using keil the error pops like "overlapping of address in 00014000H".
then...
Hi,
I am using nrf51822 and SDK 8.0.0 , SD2.1.0 as an central and SD8.0.0 as peripheral. I am following ble_app_multilink_central and ble_app_multilink_peripheral example...
Hello,
We have a custom board using nrf51822.
In keil the board is detecting at 20khz clock for SW port in the debug window, we are able to program through keil.
...
This fork of the MBED CMSIS-DAP firmware seems to be the latest updated one. The title says, 'Interface firmware providing USB CMSIS-DAP for debugging, USB MSD for programming...
Hello,
I try to change a value by using sd_ble_gatts_value_set(...). If there is a connection, this works fine. But now I have to change the value also, if there is no...
Hi again.
I'm using nRF52 DK board in Ubuntu. I can flash the device with the blinky example (I haven't yet tried the softdevice tough), but I cannot really get any traces...
20160316_113235.jpg Hi guys,
i have 20 nodes and a central in my network, that are very close to each other except central device ( All of nodes are in a approximately...
Hi,
I'm wondering why are there scan parameters on creating connection? If I refer to SD130, create connection function , there is a note which tells us that if scan is...
I have 2 existing products, one using the nRF24LE1 and the other having a 2.4GHz ANT radio. Is there a way to have the 2 products communicate wirelessly? If it is possible...
Hi.
Quest to get the toolchain working under ubuntu continues.
I've done the eclipse and jlink config as explained in the nrf51 linux tutorial (with of course keeping...
