Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
I just needed some clarification as I'm migrating from SDK 6.1 to SDK10:
app_button: There's no way to have the Button function thru the Scheduler anymore. I would...
i am using latest "master control panel" v4.0.5 and latest "nRF tool box" v1.16.2
and use sdk 5.2(its compulsory)
soft-device s110 v6.2.1(its compulsory)
and PCA10028 with...
Hello everyone,
Could anyone tell me which pins are the programming pins of the nRF51822 chip for a QFN48 packet ? How can I program it on my custom PCB?
thanks..
We are planning to use nRF52 for its superior computing power in an application. Unfortunately it appears that the throughput is more limited than on nRF51. Since we need...
Hi,
I used two 51822 modules for my project. One should send a byte and other one should receive.
I used the exact same configurations of radio examples (transmitter and...
I am trying to read an analog value on the GPIO port into my application. Looking through the examples, there aren't any that help solve this problem as the ADC example is...
I have tried to follow the installation instructions and have installed nRFGoStudio, the Keil MDK-ARM, and downloaded the latest nRF52 SDK. I also installed all of the device...
Hello,
Iam a beginner to NRF51 and Iot.
I want to be able to send messages from raspberry pie to NRF51 dk and vice versa via Bluetooth.
Iam using a generic Bluetooth dongle...
Hi ,
I've just started using a Nordic's product : an nRF51 422 QFAC develepement Kit
I was running tests by loading examples on this board when I lost the connection between...
I am building my application up on the blinky free rtos. I want to use RTC and ble stack. i am initialising RTC1 first and ble stack stact.
The problem is that I am getting...
I am using nordic nrf8002 BLE with a breakout board & not a developement kit. I gave 3.3v supply in different combinations:
(1)3.3v to vdd pin-1, GND to vss pin-4
(2)3.3v...
Is any SDK available which has single bank BLE DFU bootloader source code?
If No then is it possible to convert dual bank BLE dfu bootloader into single bank BLE dfu bootloader...
I am trying to Migrate from Sdk 6 to Sdk 11 .
Here i am facing problem in discovering Custom Characteristics .
I can successfully add service and 2 characteristics without...
Hi!
I'm building an application with one custom service containing a few characteristics, all of which are to be indicated upon. When using the Master Control Panel Android...
