Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
My program doesn't use SoftDevice.
In Reference Manual 3.0 page 52: "A HFCLKSTOP task will stop the HFCLK oscillator. However the HFCLKSTOP task can only be sent after...
Hi,
I've looked at the example codes provided by Martin in these two topics for communicating to a MPU6050 through TWI:
1- devzone.nordicsemi.com/.../ (uses SDK 9)
...
When we add a uuid will follow the steps below
err_code = sd_ble_uuid_vs_add(&nus_base_uuid, &p_nus->uuid_type);
// Add the service.
err_code = sd_ble_gatts_service_add...
I was looking the way to set different tx power values and also figuring out a small bug in the interface when you switch among payload models and payload length is >1.
Bug...
nrfgo_error.docx
Using nRFgo Studio as the interface I try to download the file “set_in _test_mode.hex” and get the error above.
What are the proper steps to get DTM...
I am trying to reset and halt the target nRF51822 under SWD protocol.
Could someone point out the register to achieve the same? I looked up the reference manual but couldn...
Hi.
I'm using PCA10028, SDK10.0.0, S130 and "ble_app_uart" as reference.
As I've researching nRF51 with Central device,
it returns
Packet 0 : 020105 0c094e6f726469635f55415254...
Hi,
I'm using long write in one characteristic but if I try to configure this characteritic with write authorization (attr_md.wr_auth = 1) it doesn't work. I need to send...
My setup is as follows
1 Gyroscope + Accelerometer
1 RTCC
1 SPI Flash device
I want to set up the PPI to periodically sample the MEMS devices and the RTCC...
Hello,
I am trying to remove the use of the frame pointers for bootloader_util.c because I am getting the error : "r7 cannot be used in asm here", but I only know how to...
I use nRF51822( BLE nano) central mode to connect annother BLE nano (ibeacon mode), then I call disconnection to the peer address. Sometime, the disconnection callback will...
hi,
i am trying to send data using ble_uart app.
in this app i am using timer difference to send data. when i am getting 1st data in uart event handler. when i am printing...
I would like to implement DFU OTA updates without the Master Control Panel, and I have a couple questions:
Is there example code for the client-side of the DFU service...
Our personal phones are set to auto-update iOS apps. Unfortunately our team all got the latest version of the NRF Toolbox app (v2.5) released on February 5th, 2016.
Previously...
