Hi
I am using the nRF54L15 DK and build a thread continueing monitor the data rate in 1 Hz, if it is lower to 800kbps I want to change to 1M; while above 800kbps I want...
Hi all,
I’m Bruce — first-time poster but have been working with the nRF9160 on and off for a while now, mainly in outdoor, power-constrained telemetry and monitoring applications...
I have a simple GATT server application with two characteristics, RX and TX. In my prj.conf, I am trying to disable pairing as follows :
I can connect to the server from...
Hello,
I am trying to use LTE connectivity on a custom board with a nRF9160 SICA B1, but i am facing issues with the modem.
With both my own app firmware and the sample...
I have searched all responses here and whatever sources I can find, but not have any success. The main problem is that existing materials appear incompatible with the 54L...
Hi, I have test the throughput using two nRF54L15 DKs and make them close to each other.
My result is:
1. My first question would be: the best througput for 2M phy is...
Hi,
We're working on a project using the nRF5340, where we interface an external NAND flash (4096 blocks) to store high-volume sensor data. We are planning to maintain an...
We use Laird BL600 module in our design. Laird engineers has informed us, that to update softdevice firmware of Nordic nRF51822 chip inside module they use Jlink adapter over...
Hello,
i've already read a lot about this topic in this forum, but now I'm unable to continue on my own. I wan't to migrate the DFU SDK emaple from Keil to GCC. I already...
Hello,
I am trying to use the nrf24l01+. But I don´t get any signal in the MISO pin. I have the same behavior in all my nrf24l01+ devices.
The MISO pin as always HIGH...
Hi,
I'm despair.
I am trying to receive data from the device with nRF2402G with a nRF24L01 + module.
The old receiver is destroyed.
I believe that I have put all the notes...
A long term problem with the Segger JLink drivers on OS X has been that for composite devices, the Seggers with both a JLink/JTag plus a USB for the UART, like those on the...
I am planning to collect data from multiple ANT sensors with nrf51 dk (like heart rate, cadence...) Collected Data will then be transmitted on a different proprietary link...
Hi!
I'm working with a NRF51822 (not a dev card) and I want to disable and enable BLE by switching a switch.
I've been looking at this thread and the functions bluetooth_sleep...
Hi,
I want to integrate Staticpasskey functionality with bootloader application in our project. as you know that in device_manager_init() function "pstorage_init()" is...
Hi all,
we have an application in which low current consumption is important, therefore we cannot use the GPIOTE IN events due to their ~1mA current consumption ( devzone...
Hello NRF,
Is it possible to have on a custom service multiple characteristics with read and notify options enabled. If yes can you show me a example or give me a hint...
hello , i work on nrf dev kit and i want to make project that the kit communicate to mobile with low current consumption. when i press button it send button press count to...
MCU : NordicSemi nRF51822-QFAC (Using custom board)
SDK Version : 6.1
Softdevice : S110 7.1
Using MDK ARM v4.6
Hi, I want to create a RTC calendar using APP_TIMER...
Hi,
I'm testing new nRF51822 Beacon v1.1.0 dedicated for smart beacon kit (pca20006). I'm using nRF Toolbox app version 1.4 and iphone 4s with ios 8.1.2. I've followed...
