Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
I cannot get a connection between Seeger Studio and a dev board from Seed Studio called nRF52832-MDK
I have added a pull-down resistor on TDO as I was getting an error that...
is advertising Complete List of 128-bit Class UUIDs(0x07) a doable ? I mean like " Complete List of 16-bit Class UUIDs " (0x03) it's not a service, just has an information...
Hi,
I'm debugging a Nordic mesh example, which is named light_switch_server_nrf52832_xxAA_s132_6.0.0_Debug, after build and go, a message appear:
sd_ble_enable: app_ram_base...
Hi All,
Hoping this is straightforward for an intermediate developer.
nRF52840-DK (matched dongle not yet in use), SDK 15.2.0, SES 4.10a (Jlink 6.40), Windows 10.
My...
Hello,
I have seen that the nRF52840 PS v1.0 specifies the RSSI_PERIOD to be 15us. I have also seen that the nRF52832 has only a RSSI_PERIOD of 0.25us (PS v1.3+) or 8us...
I need some technical information:
- the micro Host can (through a pin?) make WakeUp of the BLE module to configure it / change the operating parameters etc? - the BLE module...
While visiting the Nordic Tech Tour we were discussing the pros and cons of BLE Mesh with a Nordic employee. He recommended that we also looked at a different solution, a...
This is essentially a repeat of :
https://devzone.nordicsemi.com/f/nordic-q-a/38808/is-a-3-bit-synchronous-3-data-lines-clock-parallel-input-at-16-368-mhz-feasible
Instead...
Hi,
I am using Keiluvision 5 , nRF5-SDK version - 15.2 with SoftDevice S140, My application requires to have NFC functionality as well as UART, but when I try to merge the...
Hi. need help with dynamic routing. I have a 9 node mesh running Thread and so far i have collected and analyzed latency data and packet delivery ratio data. I need to find...
Hello there,
I am working on a project in which two devices(one is central and other is peripheral ) uses Nordic bluetooth controller for connection and data exchange. nrf51822...
Hi Nordic,
I plan to use the newest SDK (because the ATT MTU > 23 is need) for NRF52832 to develop a PC tool to connect with Nordic BLE peripheral devices, and then send...
Hi, i am using SDK15.0.0 with nrf52840 chip.
I am interfacing a SPI device in the SPIM0. The SPIM module looks working fine without a softdevice.
But when i integrate...
SDK - 15.0.0
IDE - Segger Embedded Studio
Computer Platform - Windows 7 - 64 Bit
Hi,
I am using an android phone to write a 32 byte array to the nrf52 device which...
