I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
Hi there, I have a custom board with nRF52840 and i am transferring fairly large amounts of data via uarte. I am also using my own driver. For some reason the attached device...
Hi,
I am Using NRF52840-DK Board. We are trying to transmit multiple data using NRFx_SPIM Example. for single reg read it is working fine.
please check below code is...
Hi,
I have certain doubts regarding simple message model .
1. Why simple_message_client_init or simple_message_server_init is never used? Don't we need this function to...
Hello,
I try to control led light of the thingy52 throw a MIT app inventor application.
I use the UUID : ef680300-9b35-4933-9b10-52ffa9740042
and thr characterixtic...
Page 362 of nRF52840 product specification version 1.0 March 18 shows A in 5 bits. The max entry is 0x0D (4 bits) and there has to be room for 8 entries in 32 bits. Hence...
hello, is there any way to generate DFU package without using command line. i am using segger embedded studio can directly generate dfu package in segger embedded studio please...
What is the wake time for module if i put module in system off mode in following cases .
case 1: Module will wake up by GPIO signalling
case 2: Module will wake up by...
Hello,
I need more details on DFU mode entering topic. I understand how to configure DFU to enter the bootloading mode on button press event but have dilemma about using...
I’m doing a project using NRF51822. We use P0.06 pin for PWM out while reading ADC from P0.01 P0.02 P0.03 & P0.04 .
As my experiment, when I’ve used P0.01 P0.02 P0.03 &...
Hello everyone, I was wondering if we could run IPSP over 2 BLE-supported nordic kits and ping one from another without using a BLE-Enabled router, like connecting them together...
Good morning everyone,
I am writing a custom protocol using the RADIO module and I am having a hard time understanding the address organization.....
My protocol supports...
Hi,
I want to interface an analog front-end Device through NRF52840-DK board Using SPI Interface . I want waveforms to be as Below:
which driver I suppose to use is...
Hi,
I try to Toggle ON/OFF the PWM using simple code below.
The PWM does not generate any output.
Please see code below;
/****************************************...
