Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hello , I want use nrf24lu as "Hos" and nrf51822 as 'Device'.
I need some info about nrf24xx whith gazell .but I can't find info bout those param like:
typedef enum...
Hi Engineers!
faced with a problem of SAADC impedance too small (4,7K)!
We use SINGLE ENDING 8bit mode with following settings:
NRF_SAADC_REFERENCE_VDD4
NRF_SAADC_GAIN1_4...
We are moving from a PCB using a nRF51822 QFAB module to a newer PCB using an nRF51822 QFAC module.
We observed that with the new QFAC PCB we have a significant connection...
I want to use the nrf52dk PCA10040 to remote program a BC832 chip from Fastel.
They say:
"BC832 V1 pin B3 C3 (DCC, DEC4) needs to be connected to the program can be burned...
I have an nrf52832 BLE HIDS device based, with the connection and peer handling code copied from the hids keyboard example, SDK13. I use Windows 10 as host. Setting up a connection...
I plan to keep the bonded device information in the ring buffer, but there are a few things that puzzled me:
When PM_EVT_CONN_SEC_CONFIG_REQ event is received, .allow_repairing...
Hi,
i am working ANCS example project in nrf14.1.0 SDK, s132.5.0.0 softdevice. i am able to print category of all notifications. i wanted print text message info. is it possible...
SDK13 nRF52 S132.
Hi! Correct I understand and implemented how to make interrupt?
I use gpiote.
void gpiote_init (void)
{
nrf_gpio_cfg_input(INT1, NRF_GPIO_PIN_NOPULL...
Hello,
I am using sdk12.2.2 and nrf52. I am including scan response data in my packet. But every time I am getting extra fields in my raw data as seen in nrf connect app...
Hi
I discovered I strange behaviour using twi.
I am using sdk-14.2.0, and Segger Studio. I started with the twi_scanner projected that I found in examples/peripherals...
We are using the NRF8001 in a product that is potted in epoxy with wireless charging and so completely inaccessible to any outside inputs except through bluetooth. We have...
I have already configured the usb audio class for NRF24LU1+.Then if i want to send data throught the NRF24LU1+ USB Isochronous endpoint,what should I do? Actually I have already...
use the SDK5 14.2.0, NRF52832, pca10040, the ble_peripheral\ble_app_uart\pca10040.
first, UART_EASY_DMA_SUPPORT = 1, run the uart_init(); the current is 1.2mA;
UART_EASY_DMA_SUPPORT...
Hello.
I'm having problems building example project from SDK using Segger Embedded Studio.
I'm using Segger Embedded Studio V3.30 IDE on Linux - Ubuntu 16.04. Using nrf...
I have a 24L01 + evkit in my hand and I want to burn my own program on this board, but I do not know how to burn it in. I have the following 3 questions:
Question 1: Where...
I have SD 4.0.2 + 13.0.0 secure debug bootloader, and I am trying to update it to SD 5.0.0 + 14.0.0 secure debug bootloader. It transfers the data, goes to 100%, but after...
