Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
Hello Nordic Semi,
After being in production of a battery powered remote control for over a year now, we have found many batteries going flat in the field. I have been...
In my test, with the same configuration, ANTWARE II always searches much faster than nRF51422 software.
For example. I have Master channel and Slave channel set up at 4Hz...
The test code:
#include "nrf51.h"
int main(void) {
NRF_CLOCK->LFCLKSRC = 0UL; // Internal 32kHz RC
// Start the 32 kHz clock, and wait for the start up to complete...
Hi,
I have downloaded "mastercontrolpanel.3.7.1.8567.x86.msi" and try to install on windows xp of my intel core2 laptap. But it failed with prompt like "not a valid windows...
This question devzone.nordicsemi.com/.../ reports the fact that the driver cannot be used twice without manually pin reseting teh BLE dongle.
But there is another problem...
Hi Team,
I am using nRF51 DK as packet sniffer to sniff packets between Mobile and other device.
Why it captures only advertising related packets?
After successful connection...
Hi there,
If I try to store a global variable in flash I can't store it. But when I declare this variable in the main function I can store it in flash. Can someone tell...
Hello all,
I saw their was a new update for the nRF518-SDK and I was wondering how I should update this in Keil. Is this just a simple replace folder? Replacing:
...
I inherited an ANT/BLE nRF51422 project a couple of weeks ago.
It used SDK v6.1.0 and S310 SoftDevice v1.0.0
At the time, I'm sure that the SoftDevice download said...
I'm attempting to troubleshoot problems between dev teams. One team is having some issues & I notice that their binary is slightly larger when built from exactly the same...
I am trying to use the laird BL620 module not for the smartBasic, but to run my own firmware.
I have just set it up, connected to my old segger JLink debugger.
In Keil I...
Press the Connect button on the Smart ponaep NRF Uart V2.0 recognizes the page reongil signal
Disconnect state, allow to boil for your smartphone to wait about 20 minutes...
I am pretty new to the nRF51822 in the firmware side. I have been doing hardware design for many years but need a little help getting started with firmware.
Does anyone...
When the bootloader in SDK 8.0.0 checks whether the application is valid, it only computes the CRC for the application if the CRC in the bootloader settings for that bank...
