I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
Just want to check if NRF52832 or NRF52840 can communication with iPhone 7 as instead of W1, which can transfer the data and audio from iPhone to earphone base on NRF52832...
While creating my own service I used ble_app_blinky as an example, once I opened ble_lbs.c file I saw it contains the service's declaration inside the macro:
#if NRF_MODULE_ENABLED...
I'm using nRF52 + SDK11.0.0 + s132. I have an SPI slave configured. I have 40B data being read by a master every 12ms at 1MHz SPI clock. The master is trigger to do the read...
HEY
I am using my nrf 51 dk too program the nrf51822 board externally. How I can identify the board in keil, only the 51 dk is shown in the debug settings. How i can select...
I would like to see output from NRF_LOG_DEBUG in the Rtt Viewer, to achieve that I changed (in sdk_config.h)
#define COMMON_CONFIG_LOG_LEVEL 4
#define NRF_LOG_BACKEND_SERIAL_USES_RTT...
Hi all!
These days I've developed a custom SAADC + UART program to fulfil my needs using the SAADC example in the SDK 11. I've tested it and all is working really fine...
I have 1 dongle and 2 NRF52DKs attached to my computer at the same time, when I am trying to use Keil to program just 1 board it seems like attempts to access all 3 my boards...
NFC examaples in SDK 12.2 and 13.0.0-1.alpha on nRF52832 (board PCA10040) may not work if HAL_NFC_FIELD_TIMER_PERIOD is set to a value higher than 255. HAL_NFC_FIELD_TIMER_PERIOD...
To my very limited knowledge, it has something to do with an "attribute table" of some sort. So you will have an init function, where you get to write all your attributes...
I use active scanning ，the observer will send a scan request when it hears and advertiser, and will listen for a scan response.I only see the scan event，but sent request and...
hello in nrf51 sdk, nordic has already ported freertos.
but if i want to port myself. can anyone tell me how to do it??
first i downloaded freertos from website. but then...
Hi,
I am new to nrf and trying to make some new services and characteristics for my device.
I followed the advertising , services and characteristics tutorial and was...
hello there i have ble_uart code . when i run on nrf51 dk and when i see it on mastercontrol pannel app. i got that type of screen shot!!
means when i write into characteristics...
NRF2460 is linked，I can transfer 3 byte data. But sometimes it is mute, not always.
Register I2SCNF_OUT bit6 is zero.
I am appreciate for your advices.
