Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hi,
I want to add functions of HID telephony to pickup/decline phone on nrf51822 application.
But it seems telephony usage did not work on android/ios phone, or incorrect...
hi :
I use Gzll protocol to realize 2.4G frequency hopping communication， One Device send data to One Host on Pipe2 receive. Now I use nrf24lu as "Host" and nrf51822 as ...
Hello,
My rigado BMD 200 board suddenly stopped responding. the Jlink interface cannot connect
I tried nrfjprog --recover with no success.(says cannot connect)
in segger...
I am using nrf51822 with sdk 6. I was using double bank ble dfu for the firmware upgrade. But now I have to switch to single bank dfu since my code size has exceeded the maximum...
hi ，
image 1 、
image 2、
image 3、
I now use nRF24LU1P for Bootloader upgrade, using the routine is the official website of the C# Lu1BootLdrTest project, nRF24LU1P...
Hi,
I have a nrf24lu1p usb dongle by hand and I want to know the flash size.The package marking is:
nRF D
LU1P16
1219AC
I am not sure whether the chip has a 16kB flash...
Based on multi-protocol add private agreement GZLL matching procedure, no matching success;But separate GZLL agreement can be successful, not any way to solve this problem...
Hey devs!
We'd like to add additional fields in the manifest.json when generating (or after generating) the zip file for DFU. We need these fields to make additional compatibility...
Hello,
I am using the nrf 52 dk with the soft 3.00. I am doing the Beacon Transmitter Sample Application from infocenter.nordicsemi.com/index.jsp.
I was able to compile...
Hi
I am using nrf52832 QFAA-R.
I wanted to know if there is a difference between SPIM current when SPIM is:
stopeed
started but not active.
Thanks
Yar...
While analyzing the current consumption of my nRF52832 Dev Kit I noticed that the system on low power current was significantly higher than expected. To further investigate...
i have connected the swdio , swclk , vcc , gnd , reset with the respective pins of the nrf52SDK ,but when am debug the nrf52sdk , am getting the following error.
ERROR...
Hi all,
I am testing out the BLE_APP_UART example on a NRF52DK and I am using SDK13.0 (PCA10040, S132).
I have change the app advert timeout to be 10 seconds.
I am...
I am trying to combine both the SAADC and BLE libraries to be able to read a value from my sensor on the analog pin and then send it over Bluetooth LE to a central dongle...
