I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
In the "nRF52840 Preview Development Kit v0.9.x" document, I see some power numbers listed for a run mode.
However, I am also interested in the following power numbers...
Hi,
i am using Nrf52 DK board and
i am working on TWI to get accelerometer(MMA7660) values using TWI driver. so that i am getting accelerometer values and Tap information...
Hi guys,
I bought the sparkfun breakkout board ( www.sparkfun.com/.../13990) . I also have the NRF52 DK from Nordic. I programmed the breakout board via the DK over SWD...
Hello All
softdevice version "s130_nrf51_2.0.1_API"
sdk version "nRF5_SDK_11.0.0_89a8197
i am try to flash BLE with SPI code i am not able to flash the hex..while flashing...
Hello,
Recently I was using nRF Connect app to test BLE 4.2 Communication between my Android Device and nrf51422 board. updated the hardware device so the LE Secure Connections...
Dear Nordic Developer,
I can compile and ran examples of uart, saadc, pwm_driver, pwm_libraries. Now I would like to include uart in pwm_libraries to get inputs from PUTTY...
Hello,
I integrated the relevant code from the "uart" example into the "ble_app_uart" example(this is all the code in the main routine):
uint8_t cr;
uart_init();
...
Hi all:
I use sdk11.0
<nRF5_SDK_11.0.0_89a8197\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay>
this example, scan heart sensor , sdk return...
It would be helpful to know how a packet looks like when transmitted/received from the NRF9E5 chip. I already found the algorithm to build the correct CRC, expected from the...
I have included the DFU service and a custom service in my application. During initialisation DFU service is getting initialised and later down the line my custom service...
Hello,
I have few question please about this example.
m_lesc_private_key looks unused, how to modify source to use a pre shared private key ?
is this exemple secured...
Hi!
We are trying a new module with NRF24l01+. We find a troublesome thing. On this video you can see the RF communication starts and stops with a broad-spectrum signal...
Hi :
In my application, i need to use 2 spi master (SPI0,SPI1) and spi slave the same time, but when i compiled drivers_nrf/hal/nrf_spi.h and drivers_nrf/hal/nrf_spis.h...
Hi. I'm using nRF528332, SDK13, S132.
I'm making multi-link peripheral refering to "experimental_ble_app_multiperipheral".
This example code says as below.
#define...
Hi Nordic,
In my application, I want to consume as less power as I can. In the initialization I have this functions:
static void utils_setup(void)
{
APP_TIMER_INIT...
