Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I have been experimenting with the mbed BLE Health Thermometer examples, BLE_Themometer etc. Whilst they are visible and show their name in the nRF Toolbox Health Thermometer...
Hello,
with Android 5.0 BLE central and S110 8.0 peripheral I do this:
Erase all bonds in device_manager_peripheral.c
Check that m_peer_table contains zero...
Hi,
I would like to convert a blinky project for the BOARD_PCA10040 to my own custom board. I can't find on eclipse where "#define BOARD_PCA10040" symbol is defined so I...
Hi,
I'm trying to config my device with resolvable private addr (RPA) as code below:
rpa_add.addr_type=BLE_GAP_ADDR_TYPE_RANDOM_PRIVATE_RESOLVABLE;
sd_ble_gap_address_set...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Dear Nordic Developer Zone,
In order to synchronize some tasks (motor-driving), I have recently implemented the radio notification interrupt.
In this interrupt, I toggle...
Hi,
After following all instructions on: gnuarmeclipse.github.io/.../
And after installing all Nordic Semi dependencies on eclipse.
I import on eclipse the UART_Loopback...
I'm trying to interface the twi driver with a ft200xd chip (i2c -> USB serial). I want to read the available bytes, but it requires a general call first see page 29 of www...
Hello everyone!
I got one question and could you guys help me out?
When I open the nRF Connect Mesh, after I program successfully, I can't initialize selected device while...
Hi, I'm working on a cross-platform application that needs to communicate with a custom peripheral (nRF51822 with S130 v2.0.1). I've implemented the interface for both Linux...
Long time reader first time poster upper.
I am working on a very minimal BLE send / receive scheme for a research project, and am not using a SoftDevice. I have written...
Hello,
I am noticing something curious when I attempt beacon mode for my nRF52 (sdk 12.1). Attached is an image of ubertooth packets that correctly show my ADV_NONCONN_IND...
Hi,
I am trying to communicate to PCA10040 (nRF52) dev board to communicate.
Basically i want to configure 1 board as Master another as slave, so master will initiate...
Hi,
I am using SDK 11.0 for my project development. When I tried to compile the unaltered SPI example given I got 60 Errors in my laptop. The Same SDK in other laptop is...
