I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi
i use the hrs example to transmit the data to ios.
but i need to add an option to send back data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hello,when i get connected to the phone,when i call err_code = ble_hts_measurement_send(&m_hts, &simulated_meas) and err_code = ble_bas_battery_level_update(&m_bas, battery_level...
I got the Dynastream N5 kit and have successfully used it with limited ANT work and was trying to get BLE working but can't get a driver for the USB dongle. On the 51422 product...
Hi All,
I am working in the sleep mode with system off and wake up with internal RC clock.
It function well when connected to EV board...
I see the "Emulated System...
Hi,
My application uses the softdevice 110.
Everytime, there is an event on my sensor. The sensor sends the event to my pin, which generates a gpiote interrupt . But, the...
Hi,
I'm trying to determine why a HCI DFU upload fails.
There is a log of the communication below showing the serial request/responses on the Windows side.
Is anyone...
Hi: I use dfu_single_bank_hci to update application. HCI_SLIP_UART_MODE = APP_UART_FLOW_CONTROL_DISABLED, HCI_SLIP_UART_BAUDRATE = 38400.
I use command " E:\hci_dfu_send_hex...
Hello,
In my quest of working with pstorage_raw.c I found an annoying situation when I tried to clear small portions (as I thought by using raw I would have full control...
Hello!
I have based myself on the ble_app_uart example, taken out the UART bit, and all that remains is the bluetooth functionality.
I have also implemented SPI communication...
hi guys, :)
I used SDK 6.1.0., Softdevice version is S110_nRF51822_7.0.0.
I compiled the template project. (in the "C:\Keil_v5\ARM\Device\Nordic\nrf51822\Board\nrf6310...
I want to use the UART to get and send data to another MCU on ble_app_beacon of SDK 8.1.0.
But after I add the UART function to the project, the UART can't work.
Can the...
Thanks for the SDK 8.1.1 fix. Please make it available also as a .zip in developer.nordicsemi.com/.../
Currently the fix cannot be used with a GCC toolchain as it is only...
Hi,my friend
I use the nrf905,At one end Use the PCB antenna, on the outside part of the metal.Using the results, said communication distance is shorter than 40 meters, easy...
Hi,my friend,
I have been using nrf905, but its performance is very bad.
Have a compatible chip nrf905 data communications? Working frequency 433 MHZ,100 KBPS baud rate...
uart_fsm and proc_fsm never get called.
debug on the first line of the uart_fsm and proc_fsm are do not come even
gpio toggling stops once uart interrupt received. I am...
Hi there,
I'm trying to build the Beacon source code with GCC toolchain on Ubuntu, but it's not working on Beacon Kit, there is no any response from the kit. But I tried...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...