Hello.
This may be a basic question, but please let me know. I am using nRF54L15-DK and nRF Connect SDK v3.0.2.
Is the 32MHz crystal running when the nRF54L15 program...
hi everybody: This is my first time developing an nRF chip and also my first time using VSCode After installing nRF tools and fast (3.0.0), I found that I did not see the...
We encountered some problems while debugging the nRF54L15. A total of 10 circuit boards were produced, and the chip on the board is nRF54L15CAAA. After programing the code...
Issue:
I would like to bring to your attention that I am getting an error when running the 'list command using the nrfcredstore cli utility, while trying to retrieve the...
Hi,
I have been playing around with the configs but I could not get Mode-3 to activate. What should I change for cs configs and the prj.conf file in order to activate it...
Hi there,
I am using an NRF54L15 custom board and am trying to set up a functionality using DPPI + PPIB. using a single in (1 event) and single out (1 task). I have two...
Hi,
I'm trying to get the debugger to work on my target board. I created the attached simple program to eliminate complexity.
The debugger starts, but it starts running...
I know there have been a ton of topics about this but I've tried pretty much every solution I can think of and I cannot seem to figure out why my sleep current is consistently...
Hi,
I'm facing a very critical issue.
I need to send a time critical data from a ble sensor device to a Camera device acting as a ble central device.
Due to lack of full...
I want to send data without a computer from 3 ADC sensors.
using de ble uart.
How do I set my variable to send data?
I should use in ble_nus_string_send(&m_nus, data_array...
Hello, I am trying to follow the instruction for a 2way communication between nRF chip and the client device (cell phone). Although my chip is nRF51422/ PCA10028, I have found...
hi all:
Recently, I use nrf51822 as a central to connect some older sensor, but the ble chip of the older sensor did not use nordic, so I have this problem. I develop the...
I have the Heart Rate Service(HRS) program written in embedded c. I connected a two LEDs to nrf51822 board. One LED will start blinking when advertisement starts and other...
How do I write a value to gpregret when flashing the chip?
Basically, what I need to do is be able to detect the first time the chip is powered on so I can go into a special...
In my device I want to adjust the slave latency connection parameter, however my desired min-max connection parameters are the same as during the initial connection. I find...
I have an imuduino (arduino board with nrf8001 bluetooth and some sensors) board and am trying to load some of the profiles from the nordic arduino nrf8001 bluetooth api on...
Hello
I made the switch from SDK 6.0.0 to SDK 6.1.0 with SD7. At first we didn't get it to work. We would get the error NRF_ERROR_INVALID_PARAM on dm_init(). The problem...
Hello, I set up the environment by This . Now I can ping the device on the raspberry pi.
How ever, When I run the python client example on My ubuntu-14.04 and try to connect...
Hi, where can I get access to the definition and meaning and definition of the built in functions and headers of nrf51822? for instance what does this mean: uint8_t err_code...
Hi ,
I am using nRF6.0.0, SoftDevice 7.0, for nRF 6310 hardware.
I am trying to develop a ble keyboard app with the help of Ble Keyboard Sample we have in the SDK. As...
HI,
I am currently working on a project to develop firmware for S110 nRF51822 softdevice .
Currently I have a device with the following details: Ic Version - 2, Variant...
