hi dear nordic employee:
I tried to build the project ble_app_hrs_c(pca10040) by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit(nrf52832)
2、what is my purpose?
the quality of thingy52 audio demo is not good(iphone7)...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Hi All,
i need some helps. I need a device that can connect with one phone only, so i have created a whitelist wih size of 1.
During the life of device the device can...
Hello, I'm pretty sure the new BLE 5 will come out soon and it will integrate the mesh. And if mesh needs to be done at a protocol level, it must be the softdevice.
So...
Hello iam using softdevice 110 and SDK 10.0.0, i have implimented dfu in my project, i want to update a region in EEPROM by calling pstorage_update() function before calling...
A while ago I asked this question devzone.nordicsemi.com/.../.
Yesterday I re-installed MDK 8.11 after a computer crash and I had IAR version 7.60.1 and version 8.11.2...
Hi,
I need to design a small nRF52 board On 24mm Dia 2-layer PCB, same like nRF51822 Bluetooth Smart Beacon Kit (nRF51822 Coin-Cell design). Please find the attached Schematics...
Hi everybody.
I encountered issues with the formentioned setup. In my project I'm using latest SDK 13.1, softdevice S132 v.4.0.2. I'm compiling the project with latest...
Hi to everybody,
I am working with a custom board based on the nrf52832, while trying to integrate to my existing application the DFU functionality I am having problems...
I am trying to measure the ADC on all 8 ADC pins of the nRF52 on the PCA10040. I'm noticing quite large amount on noise on floating lines (up to 0.6V). However my biggest...
We have a device with a main MCU connected to a NRF52832 for BLE communication. Our device have Battery, Heartrate and a custom service. The first implementation used a Sparkfun...
I am trying to decide what Nordic solutions would best support the application throughput requirements seen below. Distance requirements are low (1 meter each link).
...
Hi there,
I have nRF52840-Preview-DK eval board. I have downloaded the “SDK 13.1.0”. I was trying out the power management example under the folder “..\nRF5-SDK_copy\nRF5...
The 51822 PS mentions a "Nordic Trace Buffer" but doesn't seem to elaborate. I assume this is similar to the Cortex Micro Trace Buffer? Is there any more documentation available...
Hi I'm looking forward to hear if I could program an nRf51822 QFAA without using the development kit/board. The chip I have currently is a N51822- S4AT, from Wireless Tag...