i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello , i'm trying to implement the OTA DFU function in my custom designed board. I'm using NRF52 series. I started by flashing the flash I uploaded the softdevice132 v2 via...
I am using saadc to periodically sample a voltage (per about 12 seconds). The voltage cannot be shutdown and always is a value neigher zero nor VDD (1.25v, 2.5v, 1.0v, etc...
Hi,
I'm wondering if the DTM mode can be entered over the air interface on nRF bluetooth products, as specified by Core4.2 [Vol2 Part C] 4.7.1 Activation and Deactivation...
Hi,
I am looking for an solution which requires to have an BT dual mode(Smart Ready) SoC. As i require the high data rate of 2.1 and also require support of BLE 4.0.
...
HI ,
I need to interface particle measurement sensor with nrf52832. I am using S132 softdevice and SDK 11.0 for my application. I need to send commands to sensor to take...
Hi,
I feel myself a bit silly...my nRF52840 board was working the last few weeks nicely, it was visible both in nRFgo and Keil. I had the board some time in button cell...
Hello, after downloading my user app using keil, I can't seem to erase the whole chip.
This is what I'm trying to do:
erase the whole chip (nrf52840).
program S140...
Hello, when migrating a project from nrf51 to S140 nrf52840, I got an
"Error: L6218E: Undefined symbol app_error_fault_handler (referred from softdevice_handler.o)."
...
Hi,
I am quite a beginner about nrf51822. I understand that I can get RSSI during advertise mode before pairing. But I am not sure I can get RSSI after pairing. Can I get...
Hi, everyone.
Now I have found some posts about the development enviroment on Mac OS X. But none of them describes clearly how to setup the development enviroment with an...
We are trying to get serial bootloader (DFU) working. I compiled a debug version of the experimental_bootloader_secure_serial in SDK13.0.0 to see what really happens there...
Hello,
I am successfully using the following code:
float f = 23.50
char buffer[10];
sprintf(buffer, "Float = %f\n", f);
SEGGER_RTT_WriteString(0, buffer);
I...
Can nRF51 be BLE connected while it's on sleep mode? (connected by other device as Peripheral mode)
I thought, to be connected as peripheral mode, It must be advertising...
