Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Recently I have been learning ble_app_uart routine, here is a question
When receiving the message sent by the client, nus_data_handler this function will be softdevice...
Hello,
I succeeded to port s110 & sdk9 to s140 & sdk14 which was a problem before.
What we need to do now is to compare the performance of BLE devices with s110 & sdk9...
Hi, I am a beginner programmer and I have the next problem.
I am working with nRF52832 SDK 12.2 trying to send AT commands to an ESP8266. I send the AT commands byte by...
Hi all
According to errata 146 of the nRF52832 Rev 1 errata sheet V1.5, the LFRC oscillator has a frequency tolerance of 500ppm instead of 250ppm.
What are the consequences...
I have a bootloader compiled from SDK 14.0, and when I try to upgrade to 14.1, the new linker script (secure_dfu_ble_gcc_nrf52.ld) does not contain the UICR_BOOTLOADER memory...
Hi,
I'm using the nrf51822 and I want to merge Server and Client roles in one Peripheral device. I am already able to send a history of temperature and humidity measurements...
Sometimes when the method RequestData is called after receiving a notify on the characteristic, the Master Emulator seems to hang for a set amount of time before throwing...
Hi guys,
I have troubles with MCP 3.10.0.14 but the device (PCA10031) cannot be detected in my laptop (Win 7 enterprise). I actually checked it on other PCs and everything...
Hi, I have just taken on responsibility for maintaining some firmware written for the nRF24LE1. One file, radio.c, contains the copyright header:
/* Copyright (c) 2008...
Can a proxy node also be a client and server node (a controller node)?
What are the key differences between a server and a client in BLE mesh?
Can a server relay a packet...
Hi,
When I try to download code to my nRF52832 from Keil with the example "BLE ATT_MTU Throughput Example", I get this error: Error: Flash Download failed - "Cortex-M4...
i want make delay funtion by timer?
in the other MCU like PIC, AVR, stm. i find register that hold value counter and i cant set this value
for example:
timer 8 bit will...
Hello
Just to confirm:
is it OK to use 2-layer PCB with nRF52840?
In case a 4-layer is needed, when do you advise the use of a 4-layer pcb?
Basically we...
I am trying to build the project which I downloaded from github for the "A beginner's tutorial: Advertising" but I get errors for missing files when I try to build it both...
