I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi
I dont know if this ever worked or stopped working after I updated SES to v4.5
The SES v.4,5 had no nrf support so I had to back down. (not sure why the update was...
Dear Sir,
To Nordic Dev kit, a sensor is interfaced via SPI lines. Using SPI in blocking mode (Polling).
After initializing SPI communication, 2 bytes are written to the...
nrf master control panel android app sent only one byte, while sending more than one byte gives Error 13 (0xd): GATT INVALID ATTR LEN
cant we send more than one byte in...
Hi,
I'm gathering assembly specifications for a custom PCB that uses nRF5340. I don't find any specific recommended reflow profile and solder paste for assembly. I stumbled...
Hi,
Bit of a newb question but I am evaluating the Thingy 91 dev board and would like to also connect some sensors via the SPI interface. I was wondering what would be the...
Hi everyone,
I have one question just for confirmation. Can I supply the board from the VDD pins located on P1 header (Socket 1x8)? Shall I bear something in mind in that...
Hi,
We use nRF9160 and nRF Connect SDK in a device project.
Our customer have asked to declare all open soruce software modules and their licenses. Do you have such a...
Hi, I found one older question (7 months ago) with the same problem but that had no answer. Situation:
- SDK 15.3, s132 v6.1.1 - The softdevice has been enabled and ble...
Hello,
I want to add/enable logs in DFU secure bootloader exaple. For that, I have enabled following macros which are needed.
NRF_LOG_ENABLED, NRF_ATFIFO_CONFIG_LOG_ENABLED...
Dear
I am testing AGPS with my THINGY91
SIMCARD: TELIA /Norway
I got the output report:
Could you tell me what is the problem? Telia SIMCard?
Thanks,
BR
...
Hi ,
I use SES to build a project ,SDK version is 15.2.And get the err:unknown register name 'vfpcc' in asm.
This seems to happen with every file.For example :
and...
Hello all,
I am working on nRF52840 EVM board.
I am not changing any thing in nRF52840 EVM board.
I was using nRF52840 board for downloading firmware in external custom...
I'm trying to use an MMA8652FC accelerometer with the nRF52832. When I call the function nrf_drv_twi_tx() the board hard faults, stopping in <SDK>\components\libraries\util...
In the case that I used custom board, I used bootloader_secure to OTA; but after OTA, the program doesn't jump to the application, even app nrf connect notify Sent Successfully...
Dear Community;
I am running some current measurements on the NRF9160 DK. I am following the manual instructions:
1.-I am powering the NRF through external power supply...
