Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
Hi,
Can you please explain to me what bonding consists of ?
Because i want to use it in DFU from an app. I see an app where we can from the it do DFU . in Fact, the...
Hi there,
Thanks to the great tutorial from Vidar, I can play with the blinky example in Eclipse on Mac. Now I want to try the other examples, and encountered the "Error...
Dear all,
I need to know in detail the nRF51822 RF capabilities asked by bluetooth SIG.
Items 1 to 12 in chapter 1.3
See attached document RF ICS 4 1 0 (002).pdf
Thank...
Hardware: Rigado BMD-200 B using the nRF51822_xxAB
Softdevice: S110_nRF51_8.0.0
Base project: ble_app_hrs_s110_with_dfu_pca10028
Project Device: nRF51922_xxAB
Project...
Hi All,
I am trying to develop a application using radio communication, so i choosed to develop a application so it can able to tx and rx. So i integrated both rx and tx...
Hi All,
We are trying find a way to upgrade nrf51822 in the field post initial release.
I read the following posts
( devzone.nordicsemi.com/.../)
( developer.nordicsemi...
My board requires P0.9 and P0.10 to operate as GPIO pins. On the NRF52 these pins share the function with the NFC antenna. How do I make them function as GPIO pins?
I know...
Hi,
I just finished compiling my code for the nrf51 to take ADC measurements and send the hex values over ble tuart o my iphone. Now I want to see if I can send that data...
Hi, i know maybe this question was asked before, but i have a particulary issue.
I have 2 devices connected through BLE. Just when them get connected i need to send a byte...
Hello!
I need to read a string from UART, there's code below:
unsigned char GetChar(void)
{
while(!RI)
;
RI = 0;
return SBUF;
}
int Readfstr(void)
{
char...
Hardware: Rigado BMD-200 B using the nRF51822_xxAB
Bootloader: dfu_dual_bank_ble_s110_pca10028 with the device set to nRF51822_xxAB
Softdevice: S110_nRF51_8.0.0
DFU Tool...
I'm trying to use BLE library for python to communicate with one Nordic nrf51844 chipset. Because one characteristic is notification enabled, I need to enable notification...
Does there exist a white paper describing some typical PPI use cases with coding examples? The only one I've found is the peripheral/gpiote example and it is severely lacking...
