Hi.
We are doing automatic network attaching on nRF9151. This is how the flow looks:
AT%XBANDLOCK=2,...
AT+CFUN=1
AT+COPS=0
We do this until we get registered...
Dear Nordic Engineers
We found a problem on the NRF54H20. When we ran C:\ncs\v3.0.2\nrf\tests\benchmarks\multicore\idle_gpio example, the current tested on the VDDHV of...
Hi，
Platform : nrf52840, NCS 2.7.0
I would like to get the MCUBoot image swapping progress without modify the NCS, and display a progress bar on the LCD to indicate the...
I enable cs procedure and set the procdure count equals to 3, let procedure interval to be 10.
I want to change the cs channel map between procedures. so when I send HCI_LE_CS_Set_Channel_Classification...
HI ALL,
I want to obtain the status of the upgrade process using mcuboot ble, such as flashing lights when starting the upgrade, flashing lights during the upgrade, and...
Hello team,
I am using nrf54l15 dk for the devlopment and want to read the RTC counter to check for how much time my device was in sleep mode.
How to achive this?
Thanks...
Hello, I'm using nrf9151-DK kit and this UDP example: UDP . After compile and flashing I opened both serial monitors (VCOM0, VCOM1) but no output appeared. Could you please...
Hello.
I am measuring the current of nRF52832 using Power Profiler Kit (PPK).
I want to change the voltage supplied to nrf 52 arbitrarily.
I used the following case...
Hi everyone!
How to change erase range in DFU during application upgrade ? I have some data saved in flash (by psotage on 0x0007e000) and I don't want to lose them after...
Hi,
What is the advantage of using a Bluetooth SIG defined profile over a vendor specific profile? For example, if we want to transfer battery levels, can we define our...
Hi again,
Hope everyone had a great Christmas.. I did, but Santa also gave me a litte issue with my nRF52-DK..
I using a modified UART example, I have a 5min repeating...
Hello,
Basically my arrangement of NRF network is one receiver and multiple transmitter consider example 1:40 and they all configured with same address,bitrate, checksum...
Hello,
Is there a demo project that contains RTC function with softdevice.
I called the lfclk_config() and rtc_config() function before softdevice initial in main(), but...
I am using nrf52832 chip. I will be receiving time in isoFormat.
I am wondering how convert the iso format to get the date and time in my C program.
I am not using any...
Hi,
I'm develope some sensor with arduino primo, which use nrf52832 as a primary mcu.
I want to measure battery voltage level,and i find some example like:
devzone.nordicsemi...
I am using nrf52832_xxaa with SDK v11.0.
I have a requirement to write into UICR register APPROTECT to set its value to 0x00.
Is it possible?If yes, please provide a sample...
hi,
10040 nrf52dk
softdevice 132 v2.
keil ide
I am trying to read magnetometer values so that i can calibrate it using this method . For this to happen, i need magnetometer...
Hi guys,
I am using FDS module in nrf51822, sdk 11 to store and read data from flash. I have a problem about reading the data. In the documents, the function:
fds_record_open...
The problem
I am trying to build the examples contained in Bluetooth Mesh stack, but I get the following error when running cmake :
...
-- Found assembler: /usr/local...
we tried to configure two gpios as output{two separate controlling switch) at a same time.hex file formed without error but we are executing that hex file on nrf51422 dk board...
