Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
hi,
My custom board running Mesh SDK0.92 send and receive messages are normal.But after I replaced the MeshSDK in my program with Mesh SDK1.0.0, I was unable to send and...
Hello all,
I would like to establish connection between single central and two peripherals for bidirectional communication. I edited ble_multilink_central example and created...
I and new to programming the BLE devices and have just started out on the nRF52840 PDK and using Segger Embedded Studio for ARM v3.34. I have compiled and downloaded the ble_app_template...
I have to question:
1: if customer use relay node for mesh net, how much is the power consumption for one node? is there any passable to declare the power consumption to...
Hi,
I need to measure the capacitance of few capacitors for which I am currently using 3-channel CAP1203 IC from microchip.
However, I just came across the possibility of...
Hello,
I would like to establish bidirectional communication between single central and two peripherals. I referred ble multilink central example and made corresponding changes...
SDK： nRF5_SDK_11.0.0
Softdevice： s132_nrf52_2.0.0_softdevice
I set the WDT timeout in the application is 5s, when entering the BootLoader set the WDT time is 10s, how...
I am new to ble programming.
I am trying to find the best way to send json objects from android app to nrf52 chip.
What is the best way to send the json object to the...
Hello Sir,
I have developed small and compact product using nRF52832 Soc. Due to size limitation and device is portable. I have attached snap shot of power supply circuit...
Hello sir,
I am develop us product using nRF52832 chip on DK board use S132 soft device and its working well fine. So now we are designing hardware PCB of my product for...
Hello, I am trying to use adc with the uart so i can monitor the readings from adc. But when I include both drivers (nrf_drv_saadc , nrf_drv_uart) i got a confliction error...
Hello, although i have included every library and c file that is needed. i still get a declaration error. I'm almost sure that i enabled everything in sdk_config . I'm kinda...
In sd_power_system_off()，the nrf51822-board current is 2uA；And I think the current in sd_app_evt_wait() will be ~4uA(Is it correct)?
In sd_app_evt_wait(), the code...
