Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
Hello,
In sdk 14.2 configuration of LF clock with softdevice are in 2 header files (pca100xx.h and
sdk_config.h)
pca10040.h
// Low frequency clock source to be used...
Hi
I'm new in nordic development.
and i need sample code for LSM303AGR Accelerometer.
i found a LSM303AGR_ACC_Driver.h and c file but i have no idea how to use these...
Hi,
is it possible to use the onboard buck regulator of the nRF52840 to supply the 3V for the rest of the circuitry while nRF52840 is off (and also for the nRF52840 while...
I would like to be able to use the Nordic Connect app for debugging and be able to observe the current UUIDs/handles of my attributes as I change them.
I have attempted...
Hi,
I am using BL600 Development Kit(Laird).
Is it possible to develop my application on this kit using the Nordic tools( Keil IDE,SDK and soft-device)?
if yes, is...
Hello, I studying nRF51 SDK for mesh.
I have a nRF51822(PCA10028) is a Client, and three Server(two nRF52832-PCA10040, a nRF51822-PCA10028).
I did the same way with Light...
I am building an ap (based on peripheral: ble_ap_uart with custom characteristics.
I want 18 characteristics for a single service.
My software works with up to 12 characteristics...
Hello, we would like to consider this chip for a product, but I have been waiting for this to be on sale for purchase since February 2017. It's still 12 weeks out and it's...
Hi, I followed the NRF51 Guide and downloaded the file linked, and it installed the J- Link Commander, once opened it gives a prompt J-Link> and when I enter in -e command...
Hi guys,
I’m using nrf51822, s130 and sdk 12.3.0…
I would like to achieve that unknown peripheral won’t find my product or at least differentiate by device name while...
Can i use the bouder router used in thread example(on nrf52840) in the iot example to replace the Rpi bouder router so i can skip the tunnel setup(using hurricane tunnel)...
Hi everyone,
I have some questions regarding the use of EDIV and Rand in BLE Legacy Pairing.
What I understood from the specs is that these are generated during...
I think instead of releasing separate SDK for #BluetoothMesh, Nordic Semiconductor should merge #BluetoothMesh into #SoftDevice. Is it possible ?
If yes, then we can even...
We are using the nrf52840 with OPENTHREAD and would like to use the Nordic COAP application because block transfer and observe are implemented. We need to do multicast and...
Hi,
I have a development board nRF52832 and we are looking for 3rd party modules built on the same. I want some configuration changes on the modules.So, please someone help...
