Hello,
for some time I didn't have to work on my project that uses nRF Connect SDK but recently I had to work on it again and noticed that I am not able to build my before...
Hi All,
I have to implement an I2C Slave on my nrf52833 BLE project which is currently working (SDK 2.9.2)
I need some confirmation with the following step:
I have...
Hi All,
we are deciding which chip to buy in order to make our AoA trasmitter (CTE packets).
According to https://www.nordicsemi.com/Products/Wireless/Bluetooth-Direction...
I am using the 54l10 chip, and after compiling the project, I will receive a hex firmware and a zip update package. The bin firmware and hex firmware in this update package...
Hi Nordic team,
I’m working with the nRF5340 using the Bluetooth: NUS (Nordic UART Service) example from the Zephyr SDK . Since this example primarily uses the UART peripheral...
Hi,the Nordic team
I am developing Matter over Thread on nrf54l15, this device is a SED battery powered device, how can I measure the remaining battery power?
Dear Technical Support Team,
I am trying to integrate and run TensorFlow Lite Micro on the nRF5340 Development Kit using the nRF Connect SDK. I have tested both SDK version...
Hi
I have read various things about this so I would like to confirm
What is the best way to set the bluetooth address of my device ? Is it built in by nordic ?
Or is it...
Hi,
I am able to change the MAC address of the beacon using the call sd_ble_gap_address_set(BLE_GAP_ADDR_CYCLE_MODE_NONE, &gap_addr), where gap_addr is of type BLE_GAP_ADDR_TYPE_RANDOM_STATIC...
Hi, I am newbie at this field.
I have tried to configure network for communication between device nodes.
What i want to do is each device node has unique data( <30bytes...
Hi,
Is it possible to control the ouputs without connecting?
I mean something like this:
I have a nRF51DK. And I would like to detect if there are bluetooth devices...
I'm trying to get some sound out of a piezo buzzer using the PWM library here:
github.com/.../nrf51-pwm-library
My buzzer has a resonant frequency of 2,730Hz. The buzzer...
Hi all,
I am looking for some help on where to identify a problem that cropped up recently. I'm relatively new to the softdevice concept, though it seems straightforward...
Hey everyone,
I'm developing an application using the PCA10001 board. After a while my app crashes. I think this is due to un-freed memory regions. When writing similar...
Hi every one,
I work on application that read continuous analog signal with 500 sample/second and send it from nRF51822 board (1) to nRF51822 board (2) and read this value...
The BT SIG has adopted the "Indoor Positioning Service" and in there it says ...
"When a characteristic value is written, the Server may check the validity of the value...
Hi,
I need to send an audio signal through BLE connection of nRF51822 module, this signal need to quantized and sampled at rate of minimum 8000 sample/second by ADC, i...
I would like a working example of a simple application that uses soft_device (either S110 or S120) plus UART debugging.
I have read many posts in this forum about this topic...
Hi folks,
do you supply a BT Test-SW to set a module with your NRF51822 in different test modes like continuous FH etc. or to change the device to low, mid, high channel...
Hi,
I want to establish a peer-to-peer communication network between 2 nRF51422, such that both the nRF51422 can Transmit as well as Receive data. Is it possible to achieve...
hi,
as we know, the device need to being linked in 1.28s if Advertising types is BLE_GAP_ADV_TYPE_ADV_DIRECT_IND ,but my host can't link device in 1.28s,so i want to link...