Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I tried to program the beacon kit with the nfr51822_beacon_app.hex through DFU-OTA using the nRF Toolbox on an IPad, and though the upload seemed to work, the application...
How do I configure nRFgo to use the IAR I-jet rather than a segger? When I run nRFgo the nRF51 Programming tab is greyed out and it says no board connected. I presume this...
Hello, I use two nRF24L01+ modules as a transmitter and a receiver, and Atmega8515 as my microprocessors. The transmitter seems to be working as I can see the modulation on...
Hi,
Our manufacturer would like to change the recommended capacitors on the nRF51822 antenna circuit design. Here is the query:
Please check below 3 capacitors request...
I notice in the datasheet for the NRF24L01+ that the receive address needs to be programmed into the Receiver.
Our application receives data from another channel and supplies...
Hi All,
I am looking for a cost effective Chip Socket for nRF51822. The challenge with nRF51822 is that while it is the standard QFN48 package, the pitch is 0.4mm making...
hello,
I have known that Nordic has produced new nRF51 DK which already support s130. But it seems only a demo!
What's the exactly plan of BLE 4.1 and 4.2?
When can buy...
Since windows xp isn't supported any more, I need to get the evaluation kit working with a windows 7 PC. It looks like the problem is with the USB communication. Is there...
Hello,
I am using ESB protocol and there is a definition says "#define NRF_ESB_CONST_MAX_TOTAL_PACKETS 6" so how can I use maximum total packets number? I am looking higher...
How do I configure nRFgo to use the IAR I-jet rather than a segger? When I run nRFgo the nRF51 Programming tab is greyed out and it says no board connected. I presume this...
I am using SD 8.0 SDK 8.0 and MCP 3.8 I am able to find the DFUtarg service and successfully complete the transfer of my applcation (100% complete). However, upon finishing...
Hi,
I'm doing some throughput/current consumption tests with nRF51822 (on PCA10001).
My firmware has been developed starting from hrm example. I have created a custom service...
Hello,i have nrf518822 device,program the s130 (0.9 version).The centrel connect to the peripherals ,now have a problem.When pressed button1 the {event_handle(BLE_GAP_EVT_CONNECTED...
