Hello,
I am trying to use LTE connectivity on a custom board with a nRF9160 SICA B1, but i am facing issues with the modem.
With both my own app firmware and the sample...
I have searched all responses here and whatever sources I can find, but not have any success. The main problem is that existing materials appear incompatible with the 54L...
I'm pulling my hair out here. Why would syntax errors completely break the toolchain?
Every now and then ill have a syntax error which causes the build to fail, the entire...
Hi, I have test the throughput using two nRF54L15 DKs and make them close to each other.
My result is:
1. My first question would be: the best througput for 2M phy is...
Hi,
We're working on a project using the nRF5340, where we interface an external NAND flash (4096 blocks) to store high-volume sensor data. We are planning to maintain an...
Hi,
We are currently evaluating the NRF9151 for asset tracking using the AT firmware on the NRF9151 evk and an external MCU for the application firmware, emulating the final...
Hello,
We’re Bachelor’s students developing a project to estimate the angle of arrival (AoA) using a BLE antenna array on the nRF52833. Our implementation builds on Zephyr...
Hi
I'm using a SparkFun Pro nRF52840 Mini which has a UART on PIN 17(TX) and 15(RX). I've written a very simple piece of code to blink the onboard LED on and off and to...
I update my software on the nrf52840 to the SDK16 and softdevice 7.
to get this software running i update the device family pack to version 8.29.0. (keil)
If i build the...
Hi,
There's no description at all in either the written text (31.3 SPI master transaction sequence) or the timing diagrams (Figure 71: SPI master transaction) showing precisely...
Hello,
I am using nRF52840, SDK_16.0.0, SoftDevice S140 V7.0.1 and Segger for flashing the image. I am using ‘ble_app_blinky’.
In our setup we load merged hex file...
from this link
https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/getting-started-with-nordics-secure-dfu-bootloader
I gathered that nrfjprog is for flashing...
which is the Example code to test the NFC_Tag future in MDBT42 V P 512K V2 module.
i was using PCA10040 nrf52 development kit in that Example code is working same code not...
I want to disable and enable UART at runtime. I don't use DMA and interrupt.
I read this thread. https://devzone.nordicsemi.com/f/nordic-q-a/52496/nrf9160-uart-pull-up-and...
Hi.
I need to program for a set of NRF52832 with serial number from 403898368 to 403941418.
I am trying with nrfjprog --family NRF52 --memwr 0x10001080 --val %% --verify...
I am in the process of evaluating different BLE solutions for a project. The project consists of a pair of BLE-enabled devices which need to be able to go into dual-role mode...
Hi everyone
I don't really understand what the physical cell ID is. Is it a randomly generated ID created by the nRF9160 chip or a set ID within the cell?
As far as I...
Hello,
I am facing a really annoying issue when updating my SPI settings from the old nrf_drv_ towards the newer one nrfx , in SDK15. I am following the recommendtations...
Project context: -------------------- Server BLE for home trainer diy Target (Bluetooth server) : Bluefruit nRF52 The feather Library : BluefruitBLE Client : nRF Connect ...
Hello,
I am using nRF52840, SDK_16.0.0, S140 SoftDevice and Segger 4.16 for flashing the image. I am using ‘ble_app_blinky’.
1) If I enable “Just works” and without...
I have a project where one device will be both a peripheral and a central. In the central role the device will connect to a sensor. It will act based on the sensor data. In...
