Hi, I have to integrate on my MQTT application , location library using GNSS. Actually I am using location library on cellular. I want to use exclusively GNSS. I am developing...
Hi, I am using two nRF54L15 DKs running THroughput samples.
The result of coded s8 is 52kbps, which is close to the theory number.
When I change to S2 code, the result...
I'm moving to 2.9.1 and trying to get mipi working with a st7789 display. I have it working with 2.6.1 without mipi, but can't seem to get it working with mipi on a nrf5340dk...
Hello!
I want to develop a Heartrate Monitor Device which uses BLE and ANT+ using the Seeed XIAO nRF52840 Plus Board.
Now that I have the board I found out that ANT doesn...
Hi
I have one nordic nRF54L15 DK using as peripheral, I want to know the power of it. Thus, I use PPK2 to be a 1.8 voltage source and connect VOUT to P6 pin 1 and GND to...
How do I produce a signed file to flash to the network core for firmware update? I am using a child image/parent concept with the \nrf\samples\ipc\ipc_service\ project, When...
Hello,
I am working on LPN node code from the mesh SDK 3.2.0. When I run the example code, I see a current peak at every 2 sec interval. Please check the image attached...
Hello,
I managed to flash the AT command client to the board and connect to a network (both verified by COPS and CEREG)
Am I right that there is currently no AT command...
Hello,
We start using of our BLE devices with more or less permanent connection with our central BLE device, it was needed for Alisa connection.
BLE peripherals are old...
Hi,
I am a beginner in nRF52840. I want to add a channel hopping feature in the 802.15.4 example .
As per my understanding of source code, we can set the channel number...
I am looking for a way only a known/trusted device can connect and write/read information from my device. Filtering by address(white-listing) is not feasible. So what is a...
Device:
Peripheral only
Peer Manager and Bonding working
S140 radio
nRF5 SDK 15.2.0
Rigado BMD-340 module
Central == iOS devices
Our nRF5 module is controlled...
Hi, I'm on last step of developing, but I have this critical trouble. For the project, I started from ble_app_buttonless_dfu sample of SDK15.3. I added some peripheral (one...
I'm using the ble_app_grs_freertos example. I'm trying to maximize its thru-put potential for Central devices which can support the high data rates. For this I've used the...
Hi, guys,
What I do:
Add freeRTOS into ble_app_hrs example project in SDK15.0
What matter I get:
When I set NRF_SDH_BLE_GATT_MAX_MTU_SIZE as 247, the device can not...
Hi Guys,
I am using Si7021 I2C temperature sensor and I want to read the temperature value using nrf52840-DK. I connected the sensor to the 27,26 pin.
I wanted to read...
DK version: nRF5_SDK_15.0.0_a53641a
Softdevice version: s132_nrf52_6.0.0_softdevice
I am using a Fanstel BT832X SOC, which has the SKY66112 PA, on a custom PCB. The...
Hello,
I am using UART to receive data on a nRF52840 DK.
I have written some code using the Serial Port Library.
I have attached snippets of the code dealing with the...
Hi,
I'm working on a tone library. I'm using timer2 and ppi channels to generate 50% pwm signal.
It's working fine.
Now i want to add another timer comparison ( timeout...
I am trying to see if there is a way I can generate a multi frequency audio signal without additional hardware. I am talking about something similar to DTMF. The audio wave...
