Hello,
I am using SDK v2.9.1 for a Bl653 (NRF52833) and was trying to use the Nordic Academy Example for how to setup the SPI bus. The Nordic Academy example states we must...
I'm currently working on configuring the nPM1300 used in our custom board. In the product spec v1.2, it supports 2 USB compliant current limits, IBUS at 100mA and IBUS at...
Hi,
I am currently trying to enable the GPIO output interrupt functionality on my nPM1300ek with an STM32. However, I am unable to get it work correctly(I was only able...
Hi,
What is the lowest possible current consumption for nrf52840 dongle dev board with zigbee ?
I'm using this for development and i'm getting 20-30uA in idle. Is it possible...
Hello, I am working on incorporating flash logging into an application that has a GRTC-driven EGU interrupt (capture/compare event). Here is where I am setting up the EGU...
We are experiencing some ESB link failures on the receiver end of our system: nrf54L15. After minutes to hours of use the receiver will stop getting data (we know the transmitter...
Hello,
I am developing a board with the SIP nRF9151.
I'm designing the board with a shared antenna for both the GNSS and LTE signals (Ignion NN02-224).
For the antenna...
Hi all,
I have been looking for the DFU library in objective-C, without any dependency manager such as cocoapods or Carthage (we cannot use them in our solution), but...
I found the thingy hardware files and I was wondering if one can buy the flexprint antenna from you or if you can connect us to your manufacturer.
We are planning to use...
The developer kit is impressive, and I was able to get a test app running quickly using the UART thru the USB connection. However, the example BLE apps feel a great deal like...
SDK14.2 nRF52832 No SD present (using the nrf_fstorage_nvmc backend)
Question 1.
I was reading the source code for the nrf_fstorage library and saw this comment in the...
hello Nordic Team
i want to create a service ,characteristic and send data(mpu9250) over characteristc .I am using nr52 DK and mpu9250.can anybody suggest how to create...
Hello Nordic-Team,
i made a custom pcb that is based on the reference schematic of the nRF52810 QFAA with dcdc setup. However, i read that in general, the nRF52810 and nRF52832...
I would like to connect the Android Things NXP Pico board to the Nordic Thingy 52 using Bluetooth and get all sensor data from the thingy.
The Android Things board will...
Hello
Recentlly, our application with android device and nrf52, we need to do pairing process with android device in order to read characteristic from nrf52. The pairing...
I am using PCA10040 devkit and SdK11. Our application is to advertise at an interval of 100ms. Also, our application wants to spend most of the time in sleep mode. Currently...
hello , i am trying to imblement system off or system on in one of the ble central example 'ble_app_blinky_c' , i tried to refer to this example 'ble_app_template' but if...
Hi all ,
I am beginning with DFU . I complete bootloader_secure_ble and can update new firmware (application) to my NRF52832 kit via Android . And now, I have 2 kit NRF52...
hi team,
i am wondering that lot of questions regarding gps and wifi interface with nrf52 is there. why nordic is not supporting with libraries and examples for gps and...
Hi there,
I read that the nRF52840 has a maximum data throughput of around 1.3~1.4Mbps . I also read that when configured as a central it can support up to 20 concurrent...
Hello,
Can anyone point me to a good example for Polling mode using serial library?
I'm looking for an application in which I can poll the serial port for data. I went...
