Hi,
We are running into a serious issue with OTA. Specifically, we have observed that nRF52832 will not be able to perform OTA to a newer firmware given that it is previously...
Hi all,
I'm trying to characterize the UDP throughput of a Thread network consisting of nRF5340 DK devices. I saw that Espressif made a test report and they seemed to use...
I’m using a custom PCB based on the Minew ME54BS01 module (nRF54L15 SoC) for both ends of our proof‑of‑concept: one node as a GATT‑based Channel‑Sounding reflector (leveraging...
Dear DevZone support,
I'm currently evaluating nPM1300 for Lithium Polymer battery management and charging and would like to ask a question.
I understand that I can...
Hi Nordic：
We are currently testing Zigbee on the nRF54L15 platform using the Zigbee R23-add-on-V1.0.0 SDK. It has been observed that when a low-power node disconnects from...
Hello, I am using ISP1907 which has NRF52833. I get the IQ data and configuration from serial as: DF_BEGIN ['IQ', 0, 0, 11, -9, -213] ['IQ', 1, 8, 11, -209, 23] ['IQ', 2,...
I have 2x Power Profiler Kit II up and running using the Power Profiler app - started twice and with separate PPK2 instances selected, as described in another support post...
Hi, everyone. I would like to be notified about the brown-out on my device. I know about POF peripheral, but lowest possible threshold is NRF_POWER_THRESHOLD_V21 (which is...
First off, forgive me for being a newbie at ARM programming in general. In AVR this was straight forward.
I have a circuit connected like this to the ADC (P0.01 = AnalogInput2...
Hi,
I would like to transfer real time ecg data from a 3-channel adc (250 Hz per channel, 16 bits ) using nRF51822 to an android device. I would like to know if this is possible...
We are looking at using the Gazell protocol for a project. There isn't much information out there except for the "Gazell Link Layer User's Guide"
developer.nordicsemi.com...
Hi,
I've been working with a two LPC1768 boards with connections to Addicore nRF24L01+ boards.
I have not been able to successfully receive an ack on the PTX board although...
Hello
What is a typical current draw when using a PORT GPIOTE interrupt? I seem to be drawing approximately 200uA with a port event enabled. Is this normal?
I'm using...
Here: developer.nordicsemi.com/.../a00050.html
"The Bootloader/DFU with SoftDevice update example shows how a SoftDevice, bootloader, and pplication (sic) can be updated...
Hi,
I am trying to bring up custom board with 51822 CFAC-A0.
And I am continuously getting the following error as soon as the code does advertising_start().
I am using...
This comment for this line of code in twi_sw_master.c is misleading:
#define TWI_DELAY() nrf_delay_us(4) /*!< Time to wait when pin states are changed. For fast-mode the...
Hello all
I'm new to Nordic products and the Keil compiler and in order to fast-track my development I have two computers, home and work, running Keil MDK-ARM (lite) with...
As said on the topic "GAP Address types", the random static address can be changed when system boots up. I can't find any content about how to make it. Could anyone offer...
Hello,
I have a problem with getting i2c to work. What I did is enabled the 2-wire block, and tried to send various data as a master(by setting the registers), but I cant...
Hi Nordics.
I want to change SDK version of my project from SDK 6 to SDK 8.1
(actually I am trying to restart my project with new SDK 8.1)
My project base on the ancs...
