The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
Hi
AfterI updated the nrf_Connect v2.02 IOS version. I found that disconnect will happen when key in the bonding code "123456".
And my code never has this issus with previous...
Hello to all,
I am using nRF52840 DK with SDK15.0 and SES. To communicate with MS5540C I have used SPI master sample example but getting some incorrect results.
Almost...
I get a lot of error after just adding usbd source code into makefile. error: unknown type name 'NRF_USBD_Type', error: 'USBD_INTEN_ENDISOIN_Msk' undeclared here (not in a...
Hi, I am new to Nordic. We are using NRF51822 chip with S120 version of softdevice. Recently we made few changes in SDK code running on nRF51 controller chip. Is there any...
Hi, I'm using the 15.3 SDK ble_app_beacon example and want to add scan response data.
I've found some examples in the devzone, but not matching the example code in this...
Hello,
I'm currently using the nRF52840 DK and i need some help. On the other hand, i have BLE ela identifiers/sensors : elainnovation.com/bluetooth-low-energy.html
My...
I have nRF52832 running ble_app_rscs as a server, sending notification to the client every hour. I know that the client can read the values also by sending bt_gatt_read to...
dear Devzone
A disconnect error 0x22 occurred.
I know that error 0x22 is LMP_RESPONSE_TIMEOUT / LL_RESPONSE_TIMEOUT.
However, the location of the error and the reason...
I am using nRF52832 with SDK 15.2.0 for my application. The application is created taking ble_app_uart example as the base. I have modified the example to suit my requirements...
Dear,
I am working with thingy:91, v1.0.0, and running asset_tracker, I got fix location from GPS, but I am not so happy with these positions from thingy:91, sometimes the...
It seems that when I call nrf_inbuilt_key_exists() to determine if a certificate already exists, it causes a subsequent nrf_inbuilt_key_write() call to either fail or succeed...
Hi,
We are using a custom board based on nRF 52840, trying to transfer data to external QSPI flash(GD2QC).
Flash was successfully initialized and exchanged chunks of data...
Hello guys, i am trying to write a c code to read and write data to the onboard memory. i am using nrf52840 and segger embedded studio. i have used sio pins 41, 40, 04, 44...
Hi,
I already tried connecting my nRF9160 (in July) without success. I'm trying again but still no luck. If I'm right Orange has LTE-M already rolled-out in Belgium?
Anyone...
Hello,
I try to add a Thingy:91 to the nRF Cloud after I received it today. The sim card got's activated without a problem. When I try to key in my IMEI and the Pin which...
