I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
test1.hex
1.png
2.png
When i used board 0 extension board to program nRF24LE1 QFN24 OTP/Flash. it notification of error "An error occured when programming the infopage...
I'm looking for information about bandwidth utilization in crowded environments, something like a sports stadium.
Has anyone at Nordic collected data on potential congestion...
I write some function, it can run ok before I start he BLE function.
When I start the BLE function, the function can not run ok.
but , I get some data from APP throuth BLE...
Hi,
I've written code to use the "gpiote in event" to sense an interrupt from a peripheral (acceleromenter), but as soon as I enable the in event, I notice the current...
Hi everyone,
I was having RAM overflowed with stack issues which were resolved using suggestions here . Now I am facing another issue. While running mqtt I can only do...
I am trying to use the Scheduler to create my own event handler system (similar to a Ti 8051 OSAL system). I'm writing separate classes that can push data/trigger handlers...
Hi,
I use the BDS v1.1 and nRF Plugin 1.2.2 (from 23.Dec.15). My goal is to simply generate a code for the cycling power profile defined by the Bluetooth SIG. I dont change...
Hello, in the NRF Toolbox UART application for iPhone if you navigate the the UART button screen and connect to the nrf52 eveything is fine. You can exit the app (whitch goes...
After some days trying a very simple tx/rx, reading each page of the manual, looking at at this developer zone, etc. I´m still in trouble, with many distinct partial results...
Hi,
I have a problem with my SPIM read buffer.
As you can see below, my SPI device received bytes correctly and answer correctly
My code is based on SPI example...
In the simple_uart.c there is a code:
void simple_uart_put(uint8_t cr)
{
NRF_UART0->TXD = (uint8_t)cr;
while (NRF_UART0->EVENTS_TXDRDY != 1)
{
// Wait for the...
Hello. I wanted to use a receiver on a quadcopter and some becons nearby(+-5 meters). Is it possible to determine the distance IN REAL TIME to the drone?
I'm a newbie to nrf52832 and would like to ask a dumb question here: can I use radio notification to implement a dynamic advertising message? I've looked into this question...
