Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Assume that the Generic Level State is 0 and the following Generic Level Set message is received by a node.
Level: 0x7FFF Tid: 1 Delay: 0xFF (1275 ms) Transition time: 0x00...
I haven't been able to crack this one. Both pins confirmed as pull-up high using I notice when the peripheral is enabled the pins are pulled low (correct I think). Only sending...
Dear Nordic Developer Zone,
I want to change PHY configuration of ble_app_uart to 2Mbps.(SoC : nRF52811)
And I want to connect nRF52811 with iOS.(nRF connect for mobile...
Hi,
we reading out a Pressure-Sensor with TWI at the Sensor Server Model.
We get the Pressure-Data in an uint32_t and the measuring range in an uint16_t which have to...
From Mesh Model Specification 1.0.1.
"3.3.2.2.2 Receiving Generic Level Set / Generic Level Set Unacknowledged messages If the Transition Time field is included, the Delay...
I want to send larger UDP packets from nRF9160 (Thingy:91) using Serial LTE modem app.
I am not able to send more than 288 bytes of binary data.
How to send larger binary...
Hello, first, a little background info:
devzone.nordicsemi.com/.../
I want to know if I have successfully set the CCCD handle or not with my Android program.
And...
I've seen the Connectivity Bridge Application in the ncs, however I can't find any sample application for the nRF91 side showing how it can send/receive data and events from...
Hello
I have a cheap ST-link that I use heavylly to program STM arm cortex chip.
So my guess is that it should work for this case.
I am following this tutorial:
...
Hello.
When I try to import a project , it will show a error. I can't build it . Pleave view following info and help me about it . Thank you.
Harrison
BR!~
Hello,
I try to add the BLE-Template code into my existing program code, but I get the following linkage error. I have defined the following flash_placement.xml for my Segger...
Hi ,
I would like to know if a matching network is needed if I am only using a single external flex antenna for both LTE and GPS using a RF switch between them and a uFL...
Hi,
Add BLE_GATTS_EVT_RW_AUTHORIZE_REQUEST event handle at ble_lbs service in example of ble_app_blinky. but when client read the characteristics 1524 or 1525, no BLE_GATTS_EVT_RW_AUTHORIZE_REQUEST...
Environment: Windows 10 nRF Connect SDK 1.4.0 I followed all of the steps described in nRF connect SDK documentation and tried to build "Blinky" sample from zephyr as shown...
