Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hello,
My application perform reset periodically. When It does a reset the bootloader need to initialize the softdevice with SD_MBR_COMMAND_INIT_SD before calling sd_softdevice_vector_table_base_set...
Good times,
So I finally put in the tweak to enable the GPIO 9&10 pins to be used for GPIO instead of the default NFC mode. Must remember that reset for it to take effect...
Hello,
I'm testing ble_app_hrs example by nRF52832 DK.
When i change NRF_BLE_GATT_MAX_MTU_SIZE up to 158, the example project run properly.
But, when i change MTU...
Hello, I am using nrf52832 custom board, with SDK 11.0.0 and s132_nrf52_2.0.0 and trying to dim led. It seems the only suggested solution is to use the pwm driver. I was wondering...
Hello, im experimenting around with the nRF52 DK (and nRF51 DK also)
Now I have following setup on nRF52 DK:
SoftDevice: s132 nRF52 v2.0.1
Applicatoin: Example Project...
I have the option to connect nBLE51822 to MCU via SPI, UART or I2C. But is there any advantage of using SPI/ I2C interface over UART interface while connecting nBLE51822 to...
my code is below.
git_mpu9250_dmp.zip
Hello.
I use nRF52 & MPU9250.
I want to use DMP,
but I can't read data with DMP.
Because it have failed that writting firmware...
Hi there,
What is the recommended development tool setup for nRF52 Preview DK on Mac OSX?
Your guide for SDK 0.9.1 seem to rely on Keil which isn't natively available...
Hi all,
What is the difference between the app_mailbox and the nrf_queue api?
The documentation says:
A)
The mailbox library provides functions to safely exchange...
Hi team ,
I'm using sdk 12.1.0(E:\testing\examples\ble_central\ble_app_hrs_c\pca10028\s130) example.I want to change to this BLE_GAP_ADV_TYPE_ADV_NONCONN_IND in above example...
I'm using nRF52 + SDK11.0.0 + s132. I have a custom service (with a read characteristic and a separate notify characteristic). After adding the DFU service and uploading the...
Hi,
Following the docs I think I am able to write to flash but it will not read anything .
This is how I set it up, write and read :
static void sys_evt_dispatch(uint32_t...
Hi,
I used a PCA10040 dev kit with nrf52832 to test Serial Secure DFU Bootloader.
Followed all the steps in the example with my PC (Ubuntu 16.04.1 LTS 64-bit).
I...
I am using SDK 12.2.0 with soft device s132 3.0.0 using NRF52 Development Board(PCA10040).
I want to update Battery level to central device/APP.As i want to use code for...
