I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
Hello,
I am using a RFDigital Simblee module (nRF51822 chip) and an ADC with thermocouples to measure high temperatures and process the temperature data via BLE. So I'm...
I created an App with one 16 bit service and some manufacturer data, but the maximum length of manufacturer data that doesn't cause an error is 16 bytes, when in theory it...
Hello,
I have followed the instructions for openwrt on rpi2 devzone.nordicsemi.com/.../
and was able to establish connection Bluetooth 6lowpan connection between Rpi and...
HI I am working with nRF52 DK
softdevice s132 sdk v11.1
I tried out the SPI master and slave examples and they work fine (I can transfer and receive data)
I have been...
Hi,
i have an custom board, using s110 and HID example from sdk9.
After i pair and unpaired few times i get an error code :err_code = 0x8010
err_code = dm_service_context_set...
Hey! I was trying to modify s132 ble_beacon example to s140 for my nRF52840 DK but I couldn't build it in Segger Embeded Studio. What is the problem with "SEGGER_RTT_CONFIG...
Hi,
I have an nrf52 with sd 132 3.0.0 and SDK 12.2 which after turning it on I can connect to it without problems, but after some time (maybe 10-15 minutes) I can't connect...
Hi,
I am using sample ble_hrs code in SDK12.0.0 over Rigado eval Kit for BMD300. After running original code as it is device doesn't advertise. After I commented out the...
I have modified the ble_app_uart to start and stop advertise by receiving command from the uart port. If I don't delete the ble_advertising_on_ble_evt(p_ble_evt); in below...
Hi team,
Iam using (\ble_tester\examples\ble_central\ble_app_hrs_c\pca10028) this example.i want to get rssi from the advertising beacon.
Iam using this functions
sd_ble_gap_scan_start...
I see on your website that Bluetooth 5 throughput numbers are given in the graph below. And the following disclaimer is given.
"Net data throughput not including overhead...
I have taken a look the APIs which the S132 supports in nRF52 DK.
However i could not find the APIs that can initiate the channel map update ,feature exchange & version exchange...
