Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
I have been trying to understand and get the “ble_app_template” running this weekend, but I keep running into errors. For example in
static void sys_evt_dispatch(uint32_t...
Hello,
I am using "pdm sensor" with "NRF 52832". we have PDM Drivers provided by the NRF . I just want to understand how we can connect the data and clock pin with nrf ...
Dear Members,
I create a loop inside main.c using code example ant_shared channel,
it's merged with ant_plus hrm_rx, but on forever loop, it stopped on 6 loops, it's...
Hello!
A frequent question in the forum is how to enable logging messages.
My question is exactly the opposite: I experience many NRF_LOG_INFO messages from Nordic library...
I'm having some issues with a design I'm developing using the ISP1807 bluetooth SOC (contains nRF52840). Every time I apply power to my device I have to manually reset the...
Dear Members,
How can I display multiple ANT channel ?
It looks like one channel is occupying all the resource (HRM)
How can I manage the time slice between channel...
Hi,
We are building our synthetic sensors using nRF52840 for smart buildings. In some areas we are using it with BLE only, other areas we use it with BLE mesh. When we want...
Hi,
Hope you are well.
I want to send the saadc data with ble to my pc. I used the below code. I am getting the data in the right format but i am loosing some data in...
I am experience some for me strange behavior with UART0 on a nrf52832. Let me explain:
First I initialize the UART using:
APP_UART_FIFO_INIT(...)
with parameters setup...
Hi,
I am using Ozone with nrf52840.
I used this example: wiki.segger.com/Tracing_on_Nordic_Semiconductor_nRF52840
I am able to debug fine. However, I am unable to see...
SDK 16.0 and SDK 17.0 (tried both versions)
nrf52832
Segger Embedded Studio
Windows 10
When Adding an additional ADC the sleep current increases to greater than...
I am currently using SWO to get tracing data from ITM and DWT successfully.
Now I want to use parallel trace for more throughput. For that I use an FPGA, no JTrace or similar...
I have NRF51822 softdevice, STM link v2 for flashing, segger embedded studio and nrf SDK. I have seen some videos on youtube on how to flash nrf softdevice using ST link....
Hi, all.
I'm using nRF52840 pca10056. s140.
I'm communicating with the CO sensor via uart, but there's a problem.
Sensor-side set to send rx steadily, and when debugging...
Hi, does Nordic provide the "works with all hubs" Zigbee cluster?
I see this blogpost mentioning " Watch out for more information on future Zigbee 3.1 SDK All Hubs support...
