I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
In our application we have made a connection between two nrf52840 devices. with softdevice 6.1.1
normally we operate in 1Mbit mode and tx power on 8.
if we change from...
Hi,
After sending a few textmessages from the client to a server (8 bytes long approx. 10 messages/sec) i get a mesh assert on the client sometimes:
0> <t: 205648>, app_error_weak...
Hi, I'm using a PCA10056 DK board to start new development. I try to program DFU secure bootloader and SoftDevice using nRF Connect 3.0.0 My issue: - configure both hex files...
Hi All
I am recently working on CSAs (Channel Selection Algorithms) in BLE on nRF52840DK, and I am using Zephyr to develop them. I have 3 nRF52840DK, one as sniffer, the...
Hello, I've developed a BLE Mesh Network using the NRF MESH 3.1.0 SDK and the nR5F SDK 15.2.0. My network has 1 client node and max 63 server nodes: I'm using the generic...
I've been developing a solution that utilizes Mesh DFU along with the Mesh Bootloader. However, I've been seeing a frequent issue where the DFU aborts prematurely due to missing...
Dear DevZone,
I'm trying to use the Seeed CAN BUS Shield V2.0 (MCP2515) with the nRF52840 DK, but the library provided is written for Arduino One.
Do you know if any already...
Hello.
I m looking for libraries wich contains functions/methods (for example how to scan, provision, adding nodes etc. ) and solution how to use them.
I found something...
I am working with nRF 52832 platform and I soldered SB12 and cut SB10 because I wanted to feed from the external power supply and with this situation I can not connect to...
I have been working with the Nrf52840, SDK15.2 and Segger Embedded Studio 4.20a using external GNU 7 2017-q4-major. The project builds without error on the original PC. I...
Hi
How to find out which BLE version is supported for a given Nordic SDK + SoftDevice.
From which version of Nordic SDK is compliant to Bluetooth 4.2 ?
Hello,
This subject is partly a conclusion and partly a question I would like confirmed.
Our scenario is that we would like to fetch flash logs over BLE, but not really...
“EBSHSN” is reset by the RESET pin when the control CPU shifts to sleep mode when the terminal device is stopped. When measuring the current consumption in this state, about...
Hi, nordic.
I've been developing a product with ws2812B.
As I know, ws2812B is needed around 5V to work well.
And I measured voltages on 52 DK board.
VDD pin has...
