Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi all,
I have updated a custom automotive PCB and am now using the nRF51824 instead of the nRF52832 I had been using previously.
Unfortunately, I have been unable to...
I am very excited about the Bluetooth 5 LR PHY, but do you plan to release an update to the nRF5 SDK to support the newest soft device S140 v5.0.0-3.alpha?
Hello
I am new to work on nrf52,
Please can someone help me regarding how to use hardware and software pwm together. I have a need of using 13 leds , so i need 13 pwm...
Please can anyone help me on how to use(program) PWM hardware with individual loading mode? My goal is to control 12 LEDs individually with different duty cycles and playbacks...
I want measure the current of a device over a resistor. It is connected to 5V which is over VDD(3V) of nRF52 Chip.
5V--->10ohm--->Device
the differential voltage of this...
Hi,
I am using SDK v8.0.0 , Softdevice s110 and Example is ble_app_uart(peripheral).
i want to reduce a range of nRF51822 beacon(PCA20006) up to 2-3meter..
i try this...
Hi all,
Basically I am doing an exercise on the BLE system use case. Let's say I want to setup a BLE system where there are the long range BLE capabilities in Relays and...
What is a minimal length of preamble, such that nRF51 is able to safely receive a packet with? Can it be made (via some magic registers) to be as small as 4 bits? Then it...
Hello!
I'm pretty new to BLE and Nordic, and hope that someone can give me some good advice.
I'm working on a project were I have 2-4 sensors, each connected to a nRF52832...
Morning,
I ve try to flash the hex pca10040 from the examples/ble_peripheral/ble_app_hrs without success, with the flash seems ok, i can t see the device.
So as i ve...
I found this comment in fds.h as function header for fds_record_write()
* Record data can consist of multiple chunks. The data must be aligned to a 4 byte boundary, and...
Hi guys,
i was testing the connection speed from android in conjunction with advertisement time to see what will work better in my production code.
The result were:
...
Hi, Forum.
I want to make uart_bootloader without softdevice. for this, I want to prepare keil project.
I tryed this but I have some problems.
Basically,
My bootlader...
Hey there!
I am trying to switch from Keil to Eclipse.
I have followed several tutorials on this website ( like this one ) and I can easily create new eclipse project...
Hi,
I use the SDK9.0.0 S130'DFU project in the parth of pca10028\dual_bank_ble_s130\arm5_no_packs\ for testing.I found S130'DFU code is different compare to the S110 of SDK6...
