Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
I have been trying to understand and get the “ble_app_template” running this weekend, but I keep running into errors. For example in
static void sys_evt_dispatch(uint32_t...
Based on the nRFUart demo, I added a masterEmulator.DiscoverServices() block before the DiscoverPipes() block in a very similar manner. Purposed is to be able to get more...
Hi,
There is much talking about the "large data transfer" over BLE, the l2cap channel being the best option for the moment.
However, does anyone know the datarate achievable...
NRF24AP2 with MSp430F149 . ASYNC 9600 N 8 1
step 1 : reset NRF24AP2 with reset pin , and received a pulsing signal through RTS pin
step 2: send a char (0x4A) to NRF24AP2...
Hello, I am having problems getting the TWI to work. The NRF52810 needs the TWI to communicate with a EEPROM module.
Thus far ive set:
Then I try to do the TWI Scanner...
Hi,
I would like to connect the nRF52840 JTAG to a debug probe in order to debug and program it.
Can I use any debug probe or a specific one is mandatory?
Thanks...
Hi,
i am working on sdk14.2 in SEGGER EMBEDDED STUDIO, i am trying add some file to ble_app_blinky_pca10040_s132 example at the time of compilation i am getting linking...
I have run into a problem compiling with ARM Compiler 6 version.
In this case I cannot figure out the problem.
Seems the only file causeing problems (after fixing a few...
Hi
I am using SDK V. 15.3.0 and Softdevice S132 6.1.1 on a nRF52832. I am developing two devices, one of with is battery powered and one that is connected to a serial interface...
Aside from the connection interval, I'd like to know if the 2Mhz phy is enable along with Data Packet Length Extension and Connection Event Length Extension.
Is there...
The modem_info module in nRF Connect SDK returns various modem parameters to the application. The function "modem_info_params_get" fails to update the following paramters...
We are running an application in dual mode (central + peripheral) where we relay the data from the peripherals up to the top central. Is it possible to control the priorities...
As a user I need to include stdbool.h before including lte_lc.h. lte_lc.h uses the bool type but does not include the appropriate header, so I get compilation issues if I...
use sdk:11.0
Reference routine：ble_nus_c
now I use 52832 to connect a device,the service UUID like the photo.
when I only discover one service UUID,like this code...
I am using an ADC where the SPI MISO pin also acts as a data ready pin when it transitions from Hi-to-Low as detailed in the link below. I am able to configure this and it...
Hi, I am new in Mesh using nRF52840, when I try to build the light_switch example, I link to all the libraries that project need and change the SDK_ROOT to the direction of...
