After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
I have been trying to understand and get the “ble_app_template” running this weekend, but I keep running into errors. For example in
static void sys_evt_dispatch(uint32_t...
Based on the nRFUart demo, I added a masterEmulator.DiscoverServices() block before the DiscoverPipes() block in a very similar manner. Purposed is to be able to get more...
Hello All
Currently i am using nRF51422-DK (PCA10028) Board .I am planing make mesh network using nRF51 devices.i go through the mesh network introduction document which...
Hi,
I'm trying to set a button as an interrupt source. I wrote this code:
void Init(void){
pwrmng_MainStatus = PWRMNG_STS_STARTUP;
//LED
#ifdef DEBUG_LED
nrf_gpio_cfg_output...
I want to read the status of LFCLK,but I find that ,the value I have readed is awayls zero! my code is follow :
LFCLK_State = ((NRF_CLOCK->LFCLKSTAT) >> 16) & 0x00000001;...
Hi,
I had done secure OTA in nRF51 DK board using SDK 12.2.0 and s130 2.0.1 softdevice. Now, i am trying to same thing with my custom Board RL-51822-A1.
For that first...
I cloned the demo project inside the Keil MDK5, from the following path:
pack installer
device = "nRF51822_xxAC"
examples = "uart_pca10028, UART_Example_Application...
Hi,
I want to use the nRF BLE Sniffer to detect wether a connection (between my fitness tracker and smart phone) is present or not.
I am able to get the advertisement...
hi,
I am struggling to create custom service to send the simple message to the client device where both devices are nRF52832 (Server and client). when I receive the message...
I have 2 of the nRF51 Dev. kits and have been ble to run Blinky, BLE_UART and set up the 2 dev kits so that I can send data from one DK to the other and to an external board...
Hi,
I tried to flash the mbed FOTA bootloader on my nrf51 DK. I copied the bin file to the bootloader device. It said the storage on the device is to small. Now it won...
1- I am looking for Bluetooth Chip to control a DC Motor.
2- This Chip need to be small since it will be fitted on a small narrow PCB (10mm width x 110mm long PCB).
3- Chip...
Hi guys,
I want to ask if it is possible for a nrf51822 to connect to a Central ( my cell phone) without advertising. Let assume that my cell phone has nrf51822's MAC address...
Hi,
I am using st-link debugger with NRF51822 module.
I was trying to connect it openocd, but it failed. st-link is working with STM32 processor and able to flash through...
Hi,
I found a suspicious line of code.
SDK: nRF5 SDK 13.1.0 (7ca7556)
File: peer_data_storage.c
Function: pds_peer_data_read
At line number: 415
if ((*p_buf_len...
Hi,
I made a custom board with nrf51822 and custom antenna which works fine for examples which use SDK10 + SD110.
For my application it was recommended to use SDK12.3...
