Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
I have been trying to understand and get the “ble_app_template” running this weekend, but I keep running into errors. For example in
static void sys_evt_dispatch(uint32_t...
Based on the nRFUart demo, I added a masterEmulator.DiscoverServices() block before the DiscoverPipes() block in a very similar manner. Purposed is to be able to get more...
Hi,
There is much talking about the "large data transfer" over BLE, the l2cap channel being the best option for the moment.
However, does anyone know the datarate achievable...
NRF24AP2 with MSp430F149 . ASYNC 9600 N 8 1
step 1 : reset NRF24AP2 with reset pin , and received a pulsing signal through RTS pin
step 2: send a char (0x4A) to NRF24AP2...
I did a search on Real-time debug, it's said for nRF52810, in Code generation, should set Debugging Level to Level 3, and Optimization Level to None Is that true for nRF52832...
Hi,
I've installed arm-gcc and the dev kit, I've tried several different versions.
I got it to compile the examples just fine. I can compile the example in examples...
Hi,
I tried to run the pca10056 ble_app_uart on a nrf52840 dongle (pca10059) after modifying the example as suggested here on the devzone. I had to define the rx,tx,ctx...
Hi !
I wrote a "central" device which works with multiple pheripherals.
Each pheripheral (Other NRF devices and also IOS) is going throw BLE_GAP_EVT_CONNECTED and when...
I am using pyserial on OSX as well as Ubuntu to send commands to the serial CLI via the JLink virtual com port for testing, and am occasionally experiencing lost/mutated characters...
Hi everyone. I am a beginner i really need help regarding an issue. I have two nrf52832 modules, on each of them i have a sensor from which i read some values. All i want...
While testing and debugging our current state of development, sometimes our devices go totally offline (thread visible via mqtt-sn last will, no ble advertising).
I found...
Hi,
Just to share my though here.
I think it is better way to decouple the BLE and application with dual core design.
It help to get rid of application latency due to...
Hello Everyone,
We have 2 devices. 1st device is flashed with the Eddystone example & sending TLM info. The 2nd device is flashed with a modified version of the ble_app_hrs_c...
Hi.
So I'm trying to configure my SW to use two uarts (as I've understood that uarte and uart are separate modules that can be used at the same time).
As the app_uart...
Dear nordic,
I implemented a uart in BLE application its works fine.
I need to reduce current for that i enable and disable uart but when i call function disabled or enabled...
hi team,
real quick; The accuracy internal reference (0.6V) used in the SAADC is specified in COMP section of the data manual as +/-3%. The gain error in the SAADC is...
Hi,
I was just trying to build the light_switch_provisioner_nrf52840 code using Segger Embedded Studio. However, I've got a error build/light_switch_provisioner_nrf52840_xxAA_s140_6...
