We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
I see this error when transmission starts and after this RX simply do not work. Even clearing error not helping. Rx works fine when there is not any transfer done (firmware...
My environment: Keil 5; nRF52832 SDK 15.2 ; Softdevice S132 6.1.0
The uart bootloader code locate in the address: 0x70000 - 0x80000 ; (The MBR in 0x70000)
The application...
Hi,
I want to read and write MAX30100's registers. How can i do that? I tried a lot of solutions but I didn't solve that.
For example; MAX30100's address is 0x57. And...
Greetings!
I am using the SDK Mesh 3.1.0 and Softdevice 6.1.0 with the nRF52840 Dev kit: (PCA10056)
So, in my previous post ( https://devzone.nordicsemi.com/f/nordic...
I am using the nRF 15.2 SDK for Thread and Zigbee. I am currently trying to use the debugger in SES, but when I upload the code, SES complains that it can't find the source...
Hi
my devices use USB HID to PC now, and I have PC GUI.
I want use BLE send My device data to PC ( windows 10 )
if I use BLE HID services to PC
I need to do any...
Hi;
I am trying to add uart central to multilink central examble. I added some of uart part to multilink. i am trying to link two peripheral to central. when two peripheral...
Hello Nordic, for my project work i am using nrf52840 dk. with segger embeded studio i drag and drop the s140 softdevice hex file into the J-Link (chip PCA10056). and i tried...
Hello,
we are using the Nordic nRF52832, and I was hoping to update to the new SoftDevice S113 v7.0.0 as it seems like a better fit for our use cases than S132.
However...
My flash_placement.xml file is here and I am getting this error `.bootloaderSettings' will not fit in region `UNPLACED_SECTIONS'.`UNPLACED_SECTIONS' overflowed by 1024 bytes...
Hi
I have done multilink with uart and getting data from multiple ble_uart peripheral. now i have to read data from only one peripheral . what will do for that.
I am using...
Hello
I was wondering if there have been any changes in supporting IAR for nRF Mesh?
In your answer from about a year ago you wrote that you were not currently planning...
Hi,
I have some questions:
1. How does the process of getting addresses to the Nodes happen in Mesh stack? Is it automatically or I need to set it when I flashed the...
Trying to run the "Alert Notification Application" example in nRF SDK v15.3.0 on either a Windows 10 system or a Ubuntu 18.04 LTS system. Following the instructions, I can...
