Hello,
I have set nRF51822 Evaluation Kit. With its help, I would like to read the pulse of the heart rate monitor:
link text
I manage to connect to it using the...
Does the s110 stack allow retrying pairing procedure?
It looks like the stack (peripheral) always ends with disconnect upon invalid passkey.
We would like to explore the...
Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
I have built a application with IAR, and made a hex file with Intel extended. It’s works fine with nRFgo Studio. But I got problems with dfu updating from my android. I hope...
Hi. I would like to convert float32_t to uint8_t array for transmission using the ble_nus_string_send function. Can you guys please suggest the method to convert the same...
Hi
To write the some state of the device, I write two bits into the NVM memory. Thus, we get 16 write cycles to one address without erasing. I did this based on the optimization...
Hi all:
I wrote a code to directly read the register 0x43 (MPU_REG_GYRO_XOUT_H)
But the GYRO data I got is wrong
Chip: nRF51422
Board: PCA10028
Firmware: S130_nRF51_2...
Hi,
I am trying to implement a Single Bank DFU over Bluetooth for my nRF51822 (256KB / 16KB RAM) using SDK v7.1 and Softdevice 110. I am using GCC to compile the bootloader...
Hi all,
I my application I am interfacing SD card with nrf52 using FATFS file system. I am observing some weird behavior while doing this. I have two SD cards, one of 2GB...
Hi. i'm using nRF52832, SDK13, S132v4 as multi-link peripheral.
As I know, SDK13 supports multi-link peripheral refering to example "experimental_ble_app_multiperipheral...
Hi,
I am using the nRF52832 and I have use the serial bootloader to update the firmware at one of my clients place.
Actually, I have used nRFgo Studio to flash the softdevice...
Hi
I'm setting up a firmware based on the DTM example to perform certification tests.
In the DTM example firmware I see that there is a VENDOR_SPECIFIC command option...
hi,
i tried nrf51822_beacon_app.hex( C:\Nordic Semiconductor\nRF51822 Beacon v1.1.1\Source Code\nrf51_beacon\ble_app_beacon\pca20006\s110\arm_build\ ).in that we changed...
This might not be the correct place/forum to ask this question.
Since a couple of days, I am not able to step or next with gdb .
I understand that gdb needs to know what...
Hi：
Now keil4 default is to use the 16_bit THUMB instruction set, if I want to set it to start the program using the 32_bit ARM instruction set, how should we do? thanks
Hi,
After reading some questions about these topics I became a little confused.
I want to count milliseconds, so should I use Systick_Handler or use Real Time Counter...
Edit 1
To narrow down I did this... Below is ble_dfu_init() from ble_dfu.c.
uint32_t ble_dfu_init(ble_dfu_t * p_dfu, const ble_dfu_init_t * p_dfu_init)
{
uint32_t...
I am running NUS and a custom service.
I have updated vs_uuid_count = 2 in softdevice_handler.c
Following other posts on the forum, I have stepped through the code using...
