Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi everyone,
I pass few days to try to fix my issue whiteout success.
I'm working on UART example provide by SDK 10 and tried to set up a communication from my computer...
Because of the power-saving support, I want to disable the UART before Call the sd_app_evt_wait().
I referred to two following sites to know the procedure of the case....
I'm working with a nrf51422/s110 dev kit on which I downloaded the Heart rate Monitoring sample project. On my PC, using a s130 dongle, I connect the device and wrote some...
Hello,
I would like to know about the possibility of programming the nrf51822 with a Keil ULINK-ME Debug Adapter (or, if necessary, Keil ULINKpro) instead of the recommended...
Our product has a legacy interface and for security reasons I want to allow users to disable or enable the BLE via this legacy interface.
My approach to this was to disable...
I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hello,
I am having much fun with nrf52. I'd like to implement SPI read (few bytes) per GPIOTE event over PPI, the source is the GPIO event and the destination task is a...
Hi,
I'm working with the nRF51822
I'm trying to enable the use of some timer callback on the ble_app_template.
I've succefully created and started all the timers, but i...
I have a modem connected to some pins on an nRF51822 on a custom board. Two pins on the modem are active low. One is a reset pin, the other a VCC control. I want these pins...
Can the nRF51822 DEC2 pin (LDO output) be used as a 1.8V supply for low current use (say, <50uA)? Similarly, how about the 1.9V output of the buck converter (AVdd)? The current...
I'm wondering if the latest version (8.x) of S110 supports BLE 4.1's "Connection Parameter Request Procedure". This procedure is described in the BLE 4.2 spec Volume 6, Part...
I previously used Jlink to upload code to my nrf51. However, the new units I got are "locked" and I need to use nrfgoStudio to unlock and fully erase the chip.
Is there a...
Hi, I wrote a sample application to remotely control and led on nrf51822_xxaa module. in the application I was able to provide configuration to the characteristics as well...
Happened to try nRF master control panel service App.
It is a good tool.
But there probably something missing in "Scanner" screen.
I used heart rate example to do the test...
